Hima HIMATRIX F3DIO 8/8 01 F3 DIO 8/8 01 Remote I/O module with 8 Digital Inputs 8 Digital Outputs
Price:
66USD
MOQ:
1
Delivery Time:
2-3 work days
Brand:
Hima
Product Description
The safety-related F3 DIO 8/8 01 remote I/O is a compact unit built in a metal housing and equipped with 8 digital inputs, 8 digital DO+ outputs (L- ground), 2 digital DO- outputs (S+ ground), and 2 pulsed outputs. The digital outputs DO4+, DO8+, DO4-, and DO8- can also be wired as 2-pole connections when needed. The module is available in several model variants for both SILworX and ELOP II Factory, as shown in the screen referenced.
These remote I/O units connect to individual HIMax or HIMatrix controllers over safeethernet. Their job is to expand the I/O capacity of a system, and they don't run any user program on their own.
F3 DIO 8/8 Model Variants
| Designation | I/O Configuration | Operating Temp. | Programming Tool | Additional Standards (Ruggedization) |
|---|---|---|---|---|
| F3 DIO 8/8 01 | 8 DI / 8 DO / 2 Pulsed Outputs | 0...+60 °C | ELOP II Factory | Standard |
| F3 DIO 8/8 014 | 8 DI / 8 DO / 2 Pulsed Outputs | -25...+70 °C (Class T1) | ELOP II Factory | Vibration & Shock Tested: • EN 50125-3 • EN 50155 • IEC 61373 (Class 1B) |
| F3 DIO 8/8 01 (SILworX) | 8 DI / 8 DO / 2 Pulsed Outputs | 0...+60 °C | SILworX | Standard |
| F3 DIO 8/8 014 (SILworX) | 8 DI / 8 DO / 2 Pulsed Outputs | -25...+70 °C (Class T1) | SILworX | Vibration & Shock Tested: • EN 50125-3 • EN 50155 • IEC 61373 (Class 1B) |
Key Differences Summary
01 vs. 014: The 01 is the standard model. The 014 is the rugged version built for wider temperature ranges and high-vibration environments (like rail or heavy transport).
Software: You must select the model that matches your specific software environment (ELOP II Factory vs. SILworX).
While the system is being booted, all LEDs are lit simultaneously.
| LED | Color | Status | Description |
|---|---|---|---|
| RUN | Green | On | Device in RUN, normal operation |
| Blinking | Device in STOP; a new operating system is being loaded | ||
| Off | Device is not in the RUN state | ||
| ERROR | Red | On | Device is in ERROR STOP state; internal fault detected by self-tests (e.g., hardware faults or cycle time overrun). The processor can only be restarted via PADT (reboot). |
| Blinking | ERROR blinks and all other LEDs light simultaneously when the boot loader detects an OS fault in flash memory and waits for a new OS to be loaded | ||
| Off | No faults detected | ||
| PROG | Yellow | On | A new configuration is being loaded |
| Blinking | Device switches from INIT to STOP; a new OS is being written to flash ROM | ||
| Off | No configuration or OS is being loaded | ||
| FORCE | Yellow | Off | The FORCE LED of a remote I/O is not functioning; FORCE LED of the controller signals forcing of a remote I/O |
| FAULT | Yellow | On | Loaded configuration is not valid; new OS is corrupted (after OS download) |
| Blinking | Fault while loading a new OS; one or multiple I/O faults occurred | ||
| Off | No faults occurred | ||
| OSL | Yellow | Blinking | Operating system emergency loader active |
| Off | Emergency loader inactive | ||
| BL | Yellow | Blinking | OS and OSL binary defective or hardware fault (INIT_FAIL) |
| Off | No faults occurred |
Line Control Purpose
Line control is used to detect short-circuits or open-circuits and can be configured for remote I/O, e.g., on EMERGENCY STOP inputs compliant with Cat. 4 and PL e according to EN ISO 13849-1.
Connection Setup
01. Digital Output to Input Loop:
Connect the system's digital outputs TO 1 through TO 2 to the digital inputs DI of the same system.
Connect the system's digital outputs TO 1 through TO 2 to the digital inputs DI of the same system.
02. Pulsed Line Detection:
The remote I/O continuously pulses the outputs to detect:
• Short-circuits
• Open-circuits
on the lines connected to the digital inputs.
The remote I/O continuously pulses the outputs to detect:
• Short-circuits
• Open-circuits
on the lines connected to the digital inputs.
03. Configuration:
In SILworX, configure the pulsed outputs via:
In SILworX, configure the pulsed outputs via:
Value [BOOL] -> system variableIn ELOP II Factory, use:
DO[01].Value system signalNote: The variables for pulsed outputs must:
• Begin with channel 1
• Be in direct sequential order
• Begin with channel 1
• Be in direct sequential order
$2 Billion+ in Inventory Value.
20 Million+ Items in Stock.
20 Years of Technology Covered.
Why upgrade if you don't have to?
We specialize in both New and Discontinued components. Whether you are running the latest setup or maintaining a legacy system, we have the part on the shelf.
We specialize in both New and Discontinued components. Whether you are running the latest setup or maintaining a legacy system, we have the part on the shelf.
What we ship daily:
- Control: DCS, PLC, CNC, SPS
- Visualization: HMIs, Display Panels, Panel Controllers
- Motion: Frequency Inverters, Servos, Motors
- Essentials: Industrial PCs, Power Supplies
Excellence isn't a buzzword here.
It's about delivery efficiency and getting you the right part, right now.
It's about delivery efficiency and getting you the right part, right now.
Need a quote? Text me.
Contact Information
Miya Zheng
Sales Manager @ Amikon
Mobile: +86 180 2077 6792
Email: sales@amikon.cn
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
AMIKON LIMITED
Location
32D units,GuoMao Building No 388 Hubin South Road Siming district Xiamen, Fujian China
Contact Person
Miya