Pneumatic Air Cylinders

MXS Series standard silver Aluminum 16mm MXS16-50 20mm MXS20-75 Double acting cylinder Caution 1.If intermediate stops by external stopper is done, avoid ejection. If ejection occurs, it may cause damage. In case the slid table is stopped at intermediate positions by an external stopper then forwarded to the front, return the slide table to the back for just a moment to retract the stopper,then supply pressure to the opposite port to operate slide table. 2.Do not apply a load

MHY2-10D -10 to 60 ℃ ±0.2mm SMC Fluid Air Short Cuts Gas to grasp Air Cylinder Series MHY2/MHW2 Double Acting 1.Indication of effective grippng force The effective gripping force shown in the graphs tothe right is expressed as F, which is the impellentforce of one finger, when both fingers andattachments are in full contact with the workpieceas shown in the figure below. Confirmation of Gripping Point 1.Workpiece should be held at a point withinthe range of overhanging

MHL2-25D1 MHL2-40D2 Aluminum alloy SMC Nickel plated Pneumatic cylinders Advantage1.One unit can handle workpieces withvarious diameters.2.A large amount of gripping force isprovided through the use of adouble piston mechanism, whilemaintaining a compact design.3.Double-end type oil-impregnatedresin bearings with a metal backingare used for all shafts.4.Built-in dust-protection mechanismA high degree of freedom formounting5.Auto switch mountable How to Mount the Attachment to

MHL2-10D2 Double acting 0.1 to 0.6 Mpa Synthetic rubber Rack Staninless Steel Air cylinder Advantage 1.One unit can handle workpieces withvarious diameters. 2.A large amount of gripping force isprovided through the use of adouble piston mechanism, whilemaintaining a compact design. 3.Double-end type oil-impregnatedresin bearings with a metal backingare used for all shafts. 4.Built-in dust-protection mechanismA high degree of freedom formounting 5.Auto switch mountable

MXQ Series Double acting silver Aluminum 16mm MXQ16-40 25mm MXQ25-50 Slide cylinder Air Slide Table Series MXQ Integration of the guide rail and the table.Uses a recirculating linear guide for high rigidity and high precision. Air slide table for precision assembly processes. Adjuster Option Three different types of adjusting bolt have been standardized for front end rear and double end adjusters and cushion mechanisms. 1.Rubber stopper Standard stroke adjuster 2.Shock

SMC MXQ Series standard silver Aluminum alloy 6mm MXQ6-10 12mm MXQ12-20 Cylinder Air Slide Table Series MXQ Integration of the guide rail and the table.Uses a recirculating linear guide for high rigidity and high precision. Air slide table for precision assembly processes. Adjuster Option Three different types of adjusting bolt have been standardized for front end rear and double end adjusters and cushion mechanisms. 1.Rubber stopper Standard stroke adjuster 2.Shock absorber

Magnetically coupled rodless CY1S Series Aluminum alloy CDY1S25H-150 CDY1S40H-200 cylinder Warning 1. Be aware of the space between the plates and the slide block.Take sufficient care to avoid getting your hands or fingerscaught when the cylinder is operated. 2. Do not apply a load to a cylinder which is greater than the allowable value stated in the ModelSelection pages. Mounting And Caution 1. Avoid operation with the external slider fixed to the mounting surface.The

MCH2-25D Fluid Air Not required Lubrication Plug Brass Cap Resin Cylinders Guidelines for the selection of the gripperwith respect to workpiece mass 1.Although conditions differ according to theworkpiece shape and the coefficient of frictionbetween the attachments and the workpiece,select a model that can provide a grippingforce of 10 to 20 times the workpiece mass, ormore. 2. If high acceleration, deceleration or impact forces are encountered during motion, afurther margin

MHC2-16D Gas to grasp -10℃ to 60℃ SMC Solid state auto switch SUS Pneumatic Cylinder​ Advantage 1. Built-in variable throttle. 2.A solid state auto switch with an indicator light canbe mounted. 3.A large amount of gripping force is provided throughthe use of a double pistonmechanism, while maintain-ing a compact design. How to Mount the Attachment to the Finger To mount the attachment to thefinger, make sure to use awrench to support the attachment so as not to applyundue

MHC2-10D MHC2-20D Angular Type Air Double acting Single acting Argentate Cylinders Advantage 1. Built-in variable throttle. 2.A solid state auto switch with an indicator light canbe mounted. 3.A large amount of gripping force is provided throughthe use of a double pistonmechanism, while maintain-ing a compact design. Guidelines for the selection of the gripperwith respect to workpiece mass 1.Although conditions differ according to theworkpiece shape and the coefficient of

SMC Rotary actuator CDRA1 Series silver CDRA1BS80-180C CDRA1BS63-90C cylinder Caution The angle adjusting screw (angle adjustment bolt) is set at random within the adjustablerotating range. Therefore, it must be readjusted to obtain the angle that suits yourapplication. Specifications Size 10 15 20 30 40 Fluid Air (Non-lube) Max. operating pressure 0.7 MPa 1.0 MPa Min. operating pressure 0.15 MPa 0.1 MPa Ambient and fluid temperature 0℃~60℃ (No freezing) Cushion Rubber bumper

SMC Rotary actuator CDRA1 Series silver CDRA1BS80-180C CDRA1BS63-90C cylinder Caution No influence on cathode ray tubes by copper ion and fluorine resin. As standard models are already made applicable to copper free styles, they can be applied as they are. If air pressure is applied from the A side of the direction indication label, the shaft rotates clockwise. If air pressure is applied from the B side, the shaft rotates counterclockwise. Specifications Stype Pneumatic Air

SMC CDRA1 Series silver Rotary actuator with auto switch CDRA1BS32-90 cylinder Caution No influence on cathode ray tubes by copper ion and fluorine resin. As standard models are already made applicable to copper free styles, they can be applied as they are. If air pressure is applied from the A side of the direction indication label, the shaft rotates clockwise. If air pressure is applied from the B side, the shaft rotates counterclockwise. Operation Principles In the diagram

SMC CDJP2 Series silver Metal CDJP2B16-25D CDJP2B10-20D Double acting needle cylinder Caution 1.To remove and install the snap ring for the knuckle pin or the clevis pin, use an appropriate pair of pliers (tool for installinga C type hole snap ring). ln particular, usea pair of ultra-mini pliers, such as theSuper Tool CSM-07A, for removing andinstaling the snap rings on the 6mm cylinder. 2.To replace seals or to grease the cylinder during maintenance, use an appropriatepair

Standard CJP Series silver Aluminum alloy CDJPB15-25D CDJPB10-20D Pin Cylinder Caution 1.To replace seals or to grease the cylinder during maintenance, use an appropriatepair of pliers (tool for installing a C typehole snap ring). After re-installing the cylinder, make sure that the snap ring isplaced securely in the groove beforesupplying air. 2.To remove and install the snap ring for the knuckle pin or the clevis pin, use an appropriate pair of pliers (tool for installinga

Festo ADVU-32-40-A-P-A 156622 Stroke Bore Double−acting Compact cylinder Order Code Specification Piston 12 16 20 25 32 40 50 63 80 100 125 Pneumatic connection M5 M5 M5 M5 G1/8 G1/8 G1/8 G1/8 G1/8 G1/4 G1/4 End of piston rod Female thread M3 M4 M5 M5 M6 M6 M8 M8 M10 M12 M16 Male thread M6 M8 M10x1.25 M12x1.25 M16x1.5 M20x1.5 M27x2 Operating medium Filtered compressed air, lubricated or unlubricated Constructional design Piston Piston rod Cushioning Non−adjustable at both

Festo ADN-20-60-A-P-A 536352 F602 Compact ADN Series ISO 21287 Standard Pneumatic cylinder Features 1. Sensor slots on three sides for flush mounting of proximity sensors 2. Integrated cushioning rings for absorbing residual energy at high speeds and machine cycles 3. Centering holes in the end cap match centering pins ZBS Compact cylinders for maximum productivity in confined spaces, combining innovative technology, high performance and reduced installation space requirement

ISO 15551 Standard CA-50 Single ear Mounting accessory For Festo DNC series Bore 50mm pneumatic cylinder​ Standard cylinders DNC, ISO 15552 Accessories Swivel flange SNC Material: Die-cast aluminium Free of copper and PTFE RoHS-compliant All Types Diameter: mm Part NO. Type 32 174383 SNC-32 40 174384 SNC-40 50 174385 SNC-50 63 174386 SNC-63 80 174387 SNC-80 100 174388 SNC-100 125 174389 SNC-125 Dimension 1. Strcuture 2. Dimension Product show Samples You can send a sample to

CA40 174384 SNC-40 For Bore 40mm Air cylinder ISO 15552 Festo DNC Standard cylinder Accessory Single-ear Standard cylinders DNC, ISO 15552 Accessories Swivel flange SNC Material: Die-cast aluminium Free of copper and PTFE RoHS-compliant All Types Diameter: mm Part NO. Type 32 174383 SNC-32 40 174384 SNC-40 50 174385 SNC-50 63 174386 SNC-63 80 174387 SNC-80 100 174388 SNC-100 125 174389 SNC-125 Dimension 1. Strcuture 2. Dimension Product show Delivery 1. If the products we

CA32 174383 SNC-32 Swivel flange Single-ear ISO 15552 Festo DNC Standard cylinders Accessory Standard cylinders DNC, ISO 15552 Accessories Swivel flange SNC Material: Die-cast aluminium Free of copper and PTFE RoHS-compliant All Types Diameter: mm Part NO. Type 32 174383 SNC-32 40 174384 SNC-40 50 174385 SNC-50 63 174386 SNC-63 80 174387 SNC-80 100 174388 SNC-100 125 174389 SNC-125 Dimension Product show Quality Standards The company for the products are brand new original