ETO Sterilization Machine

EtO Sterilization Cycle There are at least three stages in a typical EtO sterilization cycle: Preconditioning Sterilization Aeration (Degassing) Cycle time is usually more than 14 hours. Preconditioning Preconditioning prepares the chamber environment to meet the ideal conditions for temperature, pressure and humidity. First air is removed from the chamber to allow for gas penetration. A leakage test is performed, to ensure that staff and environment are safe. Next, some

EO PROCESSING STEPS Preconditioning/conditioning Exposure to RH and temperature Ensure uniformity of these conditions Sterilization cycle Exposure to EO gas Aeration Dissipation of remaining gases DECISIVE PROCESS PARAMETERS Gas concentration >400mg/L Temperature ~100 – 140ºC Relative humidity ~35 – 80% Exposure (dwell) time 2 – 10 hours DEEP VACUUM CYCLE SHALLOW VACUUM CYCLE FACTORS AFFECTING CYCLE SUCCESS Bioburden Product/package properties Loading configuration Cycle

General introduction: Made for Hospitals : 100% ETO gas cartridges use exact dosage “as per chamber size”. No bulky cylinders to be used by inexperienced personnel, causing leakages and hence health and FIRE & SAFETY hazards. Safe and Easy Handling: ETO gas cartridges is punctured in the chamber only when proper negative pressure and humidity conditions are achieved in the chamber. Ease of Operation: Cold Cycle (40°C), Warm Cycle (55°C), 7 more user-defined cycles available.

Specification: Ventilation frequency: random Sterilizing pressure:-5∼-80Kpa Sterilizing humidity: 45∼75% RH Power: 50L1.2KW 150L2.4KW 200L2.8KW 300L3.6KW Sterilizing time:1-9 hours Ventilation time: random Sterilizing temperature:room temperature∼100oC Operating Voltage:220V±10%50HZ Newly designed liquid crystal display and man-machine interfaces Safe negative pressure circuation during the whole process and no epoxyethane leakage Microcomputer control,easiness of operation

The Ethylene Oxide Sterilization Process Pre-conditioning: Used to preheat and humidify product loads to predefined conditions. This will assure a repeatable EO sterilization process regardless of pre-processing load storage conditions Sterilization: Performed using process phases specifically designed to provide the required level of EO exposure to assure sterility for a device or family of devices Aeration: Used to accelerate out gassing of exposed product loads and to

Product Features: ● This product adopts mixed Ethylen Oxide gas, protecting from ignition and exposure , safe and dependable , non corrosive to the sterilizing load ,no pollution to environment . ● This product adopts new technology and features good energy saving and short heating time. ● Effective sterilization, easy operation. ● According to the various requirements on sterilization, you can combine the following factors freely: temperature, pressure, sterilization time,

100% ETO Low Temperature Sterilizers With Automatic Vertical Sliding Door For CSSDs and Clinics Application This series ETO gas low temperature sterilizers used in CSSD, surgeries OR, medical service centers science research institutes and hospitals for medical instruments sterilization, especially for those precise instruments unendurable to heat and humidity. Designed and manufactured to the latest standards, our ETO gas sterilizers have standard sterilizing cycles in the

Ethylene Oxide (EtO) sterilization is mainly used to sterilize medical and pharmaceutical products that cannot support conventional high temperature steam sterilization - such as devices that incorporate electronic components, plastic packaging or plastic containers. EtO gas infiltrates packages as well as products themselves to kill micro organisms that are left during production or packaging processes. This gas, mixed with air at a ratio of at least 3% EtO gas, forms an

Operational Benefits • Capacity equivalent to a small loading cart, with two stackable baskets. • Single use 100% EO cartridge means low cycle costs. • Four pre-programmed cycles between “HI-TEMP” (130º F (54º C) and LO-TEMP (100º F (38º C) sterilization with or without in-chamber aeration. • In-chamber aeration eliminates the need to transfer the load to a separate aerator. Monitors the cycle parameters and ensures that the sterilizer door(s) remain locked until the cycle is

Ethylene Oxide Sterilizer is the use of ethylene Oxide gas for the medium ,at a certain temperature,pressure ,humidity conditions ,confined in a container of items of special equipment disinfection and sterilization .with good penetration ,no damage to the goods free from corrosion ,suitable for low temperature ,pressure and humidity required in the case of sterilizaton .Applicable to medical and health ,biological engineering .the pharmaceutical industry ,food industry