IEC62368 Test Equipment

IEC 62368 Test Equipment.IEC 62368-1 TESTING AND MEASURING EQUIPMENT No. Items Description 1 Temperature and humidity chamber IEC62368-1-cl.4.1.4 Model:KP-HWS1000L 2 Test Apparatus for device forming mains plug IEC62368-1-cl.4.7 Model :KP-LJ220 Technical Parameter: 1. As per IEC60065-fig11 2. Weight: 1N, 2N. 3. Socket:UK, EU. 4. Arm of force 0-320mm 5.mension: 350*150*150 mm 3 Jointed test probe for equipment likely to be accessible to children IEC62368-1-cl.4.8 IEC 62368 -1

Gasket test-IEC 62368-1-Figure Y.1 | Compression test Following the test specified in b), the same specimens shall be cooled for a period of 24 h to the minimum temperature specified by the manufacturer or -33 °C if no minimum ambient temperature is specified and then subjected to an impact from a hammer of 1,35 kg mass falling from a height of 150 mm upon removal from the cold chamber. The hammer head shall be steel, 28,6 mm in diameter and have a flat striking surface, 25,4

IEC 60065:2014 clause 12.1.5 single arm drop tester Standard: Conforms to IEC 60065:2014 clause 12.1.5, 15.4.3 a), 12.7.3.4, IEC 60950-1 Clause 4.2.6, IEC 60598-1 Clause 4.13.4b) Application: This device is suitable for verify the drop resistance performance of audio, video and similar electronic apparatus having a mass of 7kg or less, information technology equipment having a mass of 5 kg or less, and portable lamp . Test sample: Audio, video and similar electronic apparatus

Straight unjointed version of the respective test probe applied with a force of 30N , IEC62368-1-Figure V.1 EC62368-1-cl.4.8 IEC62368-Annex V.1.3 Test method 2 Reference Standard: IEC62368-1-Figure V.1 Specification: Test Finger Length:234mm IEC 62368-1 TESTING AND MEASURING EQUIPMENT No. Items Description Photo Qty Brand 1 Temperature and humidity chamber IEC62368-1-cl.4.1.4 Model:KP-HWS1000L 1 KingPo 2 Test Apparatus for device forming mains plug IEC62368-1-cl.4.7 Model :KP

Residual Discharge Tester System Briefing: Applied to electronic remnant’s discharging experiment;auto-matically cut off at the peak and trough and come up with experimental data. Application field: electrical appliance remnant’s discharging experiment Feature: 1. automatically cut off at the peak. 2. automatically grab experimental waveforms. 3. automatically come up with the corresponding voltage value after cutting off for 1s and 2s and reduce 37% of the original time for

System introduction:a collection of video baseband signal generator,simulation TV generator,digital TV modulator,which can be applied to transmit video baseband signal(CVBS,YPbPr,SDI,HDMI),simulation TV modulating signal and digital TV signal. Application: 1. TV energy efficiency test； 2. TV display performance test； 3. TV other project test； Feature: 1. various interface outputs(CVBS,YPbPr,SDI,HDMI,simulation RF,digital RF)； 2. Meet test requirement of GB 24850-2013； 3. Meet

The restricted short circuit test device is applicable to the test of protective grounding conductor and current protection circuit breaker 1500A. The purpose of this test device is to verify that the protective connecting conductor used in the circuit protected by the device with a rated value not exceeding 25A is compatible with the fault current allowed by the overcurrent protection device, and to test the integrity of additional safety protection through such tests. Meet

IEC 62680- 1-2/ IEC 62680- 1-3 USB TYPE-C Compliance Testing Plan The EU officially issued the revised directive on universal chargers Directive (EU) in the Official communique 0J on 7 December 2022/2380 to supplement the specific implementation requirements of 3.3 (a) in RED scope of application The instructions covers 13 categories of wireless devices, including smartphones, tablets, digital cameras, headphones, handheld game consoles, portable speakers, e-books, keyboards,

IEC62109 and VDE0126 and IEC60990 inverter safety characteristic analyzer Operating Instructions 1, summary 0126-1M Photovoltaic array inverter Safety Characteristics Analysis instrument is a special measurement equipment developed according to the inverter related identification test standards IEC62109 and VDE0126 and IEC60990, an inverter for measuring the residual current of photovoltaic array inverter, distributed PV inverter, contact current, insulation resistance

IEC 62368-1-Annex E.2 Testing box | Audio amplifier normal operating temperature measurements box Test conditions for equipment containing audio amplifiers E.2 Audio amplifier normal operating conditions Equipment containing an audio amplifier shall be operated using a sine wave audio signal source at a frequency of 1 000 Hz. In the case where an amplifier is not intended for operation at 1 000 Hz, the peak response frequency shall be used. The equipment shall be operated in

IP 5X/6X dust test apparatus, IEC 62368-1 Annex Y.5.5 Protection from excessive dust 1. Standard IEC60529; IEC60598-1:1999; GB/T10485-2008 , IEC62368-1 2. Technical parameters Internal dimension 1000 X 1000 X1000 W*H*D mm metal mesh diameter 50um Talcum powder dosage 2Kg/m³ air velocity No more than 2m/s The Talcum powder amount 2kg/ m³ Internal material sus304 corrosion resistant plate External material A3 plate plastic spraying powder Door tempered glass door Power AC 220V

Water spray test apparatus , IEC 62368-1 Annex Y.5.3 Water spray test Y.5.3 Water spray test The water-spray test apparatus, using fresh water, is to consist of three spray heads mounted in a water supply pipe rack as shown in Figure Y.2. Spray heads are to be constructed in accordance with the details shown in Figure Y.3. The outdoor enclosure is to be positioned in the focal area of the spray heads so that the greatest quantity of water is likely to enter the outdoor

magnified glass with a resolution of 0.1 mm , magnified glass , IEC Test Equipment 8.5.5.2 Test method For the protection against the effects of a high pressure lamp failure, the following test is performed as follows: – lamp assemblies considered MS3 parts during field replacement are tested separate from the equipment; – lamp assemblies only considered MS3 parts during operation, may be tested separately,or as normally installed in the equipment, or both. An explosion of

1. Product Overview 1.1 Product introduction The MS2670PN series tester is a program control withstand voltage tester based on electrical strength test. The voltage rises according to the set time gradient. It has 4 sets of memory modes, RS232 and PLC interfaces, and can be customized with added 485 interfaces. The test circuits provided by this series of testers meet the Household and Similar Electrical Appliances - Safety Part I General Requirements (4706.1), Testing

Use 5.6 inch TFT (640*480) to display the setting parameters and test parameters, and the display content is eye-catching and rich;  The tester can store the test results in the format of EXCEL table in U;  Software can be upgraded through U disk;  Compliance leakage current test Human body network: GB9706.1(IEC60601-1)/GB4793.1(IEC61010-1)/GB4706.1(IEC60335-1)/GB4943.1(IEC60950-1)/ GB8898(IEC60065)/GB7000.1(IEC60598-1)/GB/T12113(IEC60990) standard; Leakage current

IEC62368-1-clause 8.8 Handle strength test method , 75mm width, several weights, scale, timer 8.8.2 Test method A weight shall be uniformly applied over a 75 mm width at the centre of the handle, without clamping. The weight shall be the equipment weight plus an additional weight as specified below: – for MS1 equipment with two or more handles, a weight that exerts a force of three times the weight of the equipment; NOTE No tests apply to MS1 equipment having only one handle.

IEC 62368-1-Annex Y.4.4 Compression test-1.35kg hammer Following the test specified in b), the same specimens shall be cooled for a period of 24 h to the minimum temperature specified by the manufacturer or -33 °C if no minimum ambient temperature is specified and then subjected to an impact from a hammer of 1,35 kg mass falling from a height of 150 mm upon removal from the cold chamber. The hammer head shall be steel, 28,6 mm in diameter and have a flat striking surface, 25

IEC 60950-1 clause 2.10.8.4 Automatic Abrasion Resistance Tester / Printed Circuit Abrasion Strength Device Application: The device is used to check abrasion strength of printed circuit boards scratches are made across five pairs of conducting parts and the intervening separations at points where the separations will be subject to the maximum potential gradient during the tests. Technical Parameters: 1. As per clause 2.10.8.4 of IEC 60950-1/IS 13252-1 1. The scratches are

IEC60950 Abrasion Resistance Test For Checking Abrasion Strength Of Pcb Scratches 1.Application: The device is used to check abrasion strength of printed circuit boards scratches are made across five pairs of conducting parts and the intervening separations at points where the separations will be subject to the maximum potential gradient during the tests. The scratches are made by means of a hardened steel pin, the end of which has the form of a cone having a tip angle of 40°

Terminal probe Reference Standard: IEC62368-1-Figure V.5 Technical Parameters: 1, Test Probe Length :13mm 2, Test Probe Diameter:1.0 (0, +0.005)mm 3, Dam- sphere Diameter:35mm 4, Handle Diameter:10mm 5, Handle Length :100mm 6, According to IEC61032 figure 4 (the Test probe D)