IEC62368 Test Equipment

magnified glass with a resolution of 0.1 mm , magnified glass , IEC Test Equipment 8.5.5.2 Test method For the protection against the effects of a high pressure lamp failure, the following test is performed as follows: – lamp assemblies considered MS3 parts during field replacement are tested separate from the equipment; – lamp assemblies only considered MS3 parts during operation, may be tested separately,or as normally installed in the equipment, or both. An explosion of

The restricted short circuit test device is applicable to the test of protective grounding conductor and current protection circuit breaker 1500A. The purpose of this test device is to verify that the protective connecting conductor used in the circuit protected by the device with a rated value not exceeding 25A is compatible with the fault current allowed by the overcurrent protection device, and to test the integrity of additional safety protection through such tests. Meet

Socket Outlet Torque Balance​ Product details: Model KP-LJ2: The Plug torque tester is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus as shown in IEC60065 Figure 11. A device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets. The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the

Twisted Wire Test Apparatus Product Description Standard:IEC60851-5-figure 2 Loads applied to the wire and number of twists

IEC60065:2014 clause 12.5 Figure 9 Test Plug For Mechanical Tests On Antenna Coaxial Sockets Standard: IEC60065:2014 clause 12.5 Figure 9. Application: It is used to test the antenna coaxial socket which is installed on the device and equipped with parts or components which isolate the hazardous live parts and accessible parts. Its structure should be able to withstand the expected mechanical stress that might encounter during the use process. Test sample: Audio, video and

IEC60065:2014 clause 8.21, figure 16 Mandrel Test Device Non Separable Thin Layer Material Anti Damage Strength Verification Device Standard: Confirm to IEC60065:2014 clause 8.21, figure 16, IEC60950 Application: Insulation anti damage strength verification for non separable thin layer materials. Test sample: Non separable thin layer material. Feature: The position of 10°and 230°are set with mechanical limit, not only to ensure the accuracy of the test angle, but also to

IEC 62209-3 Fast SAR Automatic Measurement System,CSAR3D - SAR System With Novel Vector Array Technology,iec 62209 test equipment three dimensional visualisation of specific absorption rate visualisation of SAR peak values control of base station simulators automatic generation of reports SAR: the full English name of SAR is specific absorption rate, which is generally called electromagnetic wave absorption ratio or specific absorption rate in Chinese. It is the electromagnet

IEC 62209-3 Fast SAR Automatic Measurement System,CSAR3D - SAR System With Novel Vector Array Technology SAR: the full English name of SAR is specific absorption rate, which is generally called electromagnetic wave absorption ratio or specific absorption rate in Chinese. It is the electromagnetic wave energy absorption ratio of mobile phone or wireless product, which is defined as: under the action of external electromagnetic field, induced electromagnetic field will be

RD4L IT Test Equipment Battery Capacity Voltage Discharge Resistant Tester Battery capacity voltage discharge resistant tester RD4L 1 Introduction 1.1. Title Residual Discharge Automatic Test Software 1.0 Instruction Manual. 1.2. Purpose The purpose of this document is to explain how to use the residual discharge automatic test software V1.0 ;make it easier for users to operate. 2. The main program control and display interface Residual discharge automatic test software V2.0

RDL-320 Tv Signal Tester Transmission System Energy Efficiency And Display Performance Test RDL-320 TV Signal Transmission System 1 Overview 1.1 Product Introduction The product is used for digital TV testing and provides test signals for TV test experiments. The product can generate test signals CVBS, YPbPr, SDI, HDMI, and RF antenna interfaces to meet the test requirements of the main TV interface. 1.2 Application areas: 1. TV energy efficiency test; 2. TV display

Terminal probe Reference Standard: IEC62368-1-Figure V.5 Technical Parameters: Each terminal is tested with the straight test probe of Figure V.5 with a force of 1 N ± 0,1 N and with the length limited to 20 mm ± 0,2 mm. 1, Test Probe Length :20mm 2, Test Probe Diameter:1.0 (0, +0.005)mm 3, Dam- sphere Diameter:35mm 4, Handle Diameter:10mm 5, Handle Length :100mm 6, According to IEC61032 figure 4 (the Test probe D)

Wedge probe IEC62368-1-Figure V.4 Reference Standard: IEC62368-1-Figure V.4 Calibration Certificate:Figure V.4 Wedge probe.pdf Technical Parameters: Test finger length 234mm Knurled length 30/30/40mm Material stainless steel and nylon Reference IEC62368,IEC60950 Tolerances on linear dimensions without specific tolerances: ≤25 mm: ±0,13 mm >25 mm: ±0,3 mm

IEC 60950 Figure 2C / IEC62368-1 Figure V.3 Blunt Probe Testing the Limited Access to Telecommunications Voltages The Blunt probe is required in IEC62368,IEC 60950,IEC 60065, UL and CSA Standards. It is used to check the limited access to Telecommunications voltages (TNV), mainly telephone jacks and operator areas. Satisfies basic standard for telecom product safety. Meets Requirements for Testing Standard(s) including but not limited to:IEC 60950 UL 60950 EN 60950 CSA 950

Jointed test probe for equipment not likely to be accessible to children Reference Standard: IEC62368-1-Figure V.2 Specification: Knurled Finger Diameter:12mm Knurled Finger Length:80mm Baffle Plate Diameter:50mm Baffle Plate Length:100mm Baffle Thickness:20mm Tolerances on dimensions without specific tolerances: – 14° and 37° angles: ± 15 ′ – on radii: ± 0,1 mm – on linear dimensions: ≤ 15 mm: 0 ,-0.1 mm > 15 mm ≤ 25 mm: ± 0,1 mm > 25 mm: ± 0,3 mm NOTE This jointed test

Reporting Automatic Printer / Report Paper Automatic Stamp And Binding Equipment 1. Product Overview 1.1 Type of equipment This product is based on paper manual seal nail cumbersome, time-consuming and developed automation equipment, mainly used for office. Office automation, labor liberation, labor costs savings, improve work efficiency is our consistent pursuit. Model KP -G1: is mainly used for multiple sheets of paper at the same time steel printing and nail, can be

1. Product Name: pulse test generator 2. Product model:KP-PRM65 3. Standard basis:IEC62368-1:2018 Appendix D and figure D.1 4. Product introduction: The pulse test generator is manufactured according to the requirements of Appendix D and figure D.1 of iec62368-1. 5. Standard requirements Circuit type Test pulse C1 C2 R1 R2 R3 1 10/700us 20uF 0.2uF 50Ω 15Ω 25Ω 2 1.2/50us 1uF 30nF 76Ω 13Ω 25Ω remarks If the same results can be obtained, an alternative test generator can be used

USB Type-C Connectors and Cable Assemblies Compliance - Figure D-1 Example of 4-AxIs Continuity Test Fixture Table D-1 Force and Moment Requirements Receptacle configuration with respect to mounting surface Force at 15 mm from receptacle shell mating edge (N) Moment with respect to receptacle shell mating edge (Nm) Right angle 20 0.30 Vertical 8 0.12 The continuity across each contact shall be measured throughout the application of the tensile force. Each non-ground contact

Vicat test -IEC62368 - clause - 5.4.1.10.2 Description: Vicat softening temperature uses single-chip control, LED digital display of temperature and deformation on the operation panel to set test parameters and test results can be read. During the test, the test temperature monitoring can be implemented, test the deformation; This series of simple structure, easy to operate, after the end of the experiment results are automatically stored. Comply with IEC62368-1,IS075 (E),

Test plug for mechanical tests on antenna coaxial sockets Reference Standard: IEC60065-figure 8 Specification: Endurance test: A test plug as shown in figure 8 is inserted and withdrawn from the socket 100 times. Care is to be taken not to damage the socket intentionally during insertion and withdrawal of the test plug.

IEC60065 clause 12.1.1 Bump Test Machine for Electronic Apparatus Testing with A Mass Over 7 kg I. Descriptions The KP-GT065 Bump Tester Machine is designed as per IEC60065-clause 12.1.1 ,which is used to tesr audio, video and similar electronic apparatus Bump test Apparatus with a mass exceeding 7 kg are subjected to the following test: The apparatus is placed on a horizontal support of wood which is allowed to fall 50 times from a height of 5 cm onto a wooden table. After