Electrical Safety Test Equipment

IEC62196-1 Clause 26.4 EV Plug and Vehicle Connector Cable Bending Test Apparatus for Flexing Test 1. Introduction of cable bending test apparatus Cord bending test apparatus is designed according to IEC62196-1 clause 26.4 figure 20 and table 14, it is applied to do mechanical load flexing test of the non-rewirable accessories of ev plug and vehicle connector. Test method: The sample is fixed to the oscillating member of the apparatus so that at the middle of travel, the

IEC 62196-1 Clause 25.3 Cord Anchorage Pull Force and Torque Tester for EV plugs and Vehicle Connectors 1. Description of Cord anchorage pull force and torque tester The cord anchorage pull force and torque tester is designed according to IEC62196-1 clause 25.3 figure 17 and IEC60309-1 clause 23.3, It is used to test tension and torque on the electric vehicle plug and vehicle connectors provided with a flexible cable, it shall not be possible to push the cord into the

IEC 62196-1 Test Apparatus For Checking Damage To VE Conductors with 10Rpm 1. Introduction of apparatus for checking damage to VE conductors:The apparatus for checking damage to EV conductors is designed to meet the test requirements of IEC62196-1 clause 13.3 figure 12, IEC60884-1:2022 clause 12.2.5 and figure 13, IEC60669-1 clause 12.2.5 and figure 9, IEC62052-31 clause 6.9.7.3 (for flexion test). The apparatus adopts guide rail screw structure, it consists of case, mass,

IEC62368-1 Steel Disc Aluminum Ring Aluminum Foil for Temperature Rising Test Introduction: 1. The steel disc is designed according to IEC62368-1 figure 47, the disc is made of steel 1.1011/RFe 160, and configure with K type thermocouple, the end of thermocouple equip with plug. 2. The aluminum Ring is designed according to IEC62368-1 figure 48, the ring is made of aluminum, and configure with K type thermocouple, the end of thermocouple equip with plug. 3. The Aluminium Foil

Blunt Probe as Per IEC60950, IEC60065 and IEC62368-1 for Testing TNT Circuit 1. Introduction The blunt probe is designed according to IEC60950 figure 2C, IEC60065 figure B1, IEC62151 figure 3, UL6500 figure B.1, IEC62368-1 figure V.3. It is applied to check if the exposed parts of TNT circuits of information technology equipment has adequate protection. 2. Specification Length of the probe 80mm±0.2mm Radius of probe R6＋0.05mm Diameter of probe φ12＋0.05mm Diameter of stop

Tracking Index Test Device 1. Introduction of tracking index test device The tracking index test device is applicable for research, production and quality inspection departments of lighting equipment, low-voltage electrical appliances, household appliances, machine tool appliances, motors, power tools, electronic instruments, electrical instruments, and etc.. It is also suitable for insulating materials and engineering plastics, electrical connectors and auxiliary parts

Apparatus for Checking Damage to Conductors as Per IEC60884-1 Clause 12.2.5 and Figure 13 1. Introduction The apparatus for checking damage to conductors is designed to meet the test requirements of IEC60884-1:2022 clause 12.2.5 and figure 13 and IEC60669-1. It is applied to checking if the terminal with screw clamping or screwless clamping can withstand the mechanical stress in normal use, and judging whether the design and structure of the screw clamping terminal meet the

5KV AC/DC Withstand Voltage Tester for Testing Medical Equipment as IEC60601-1 1. Introduction The RK2672CY medical withstand voltage tester has all the functions of the conventional withstand voltage tester, and has added an arc (flashover) detection function. Through an external oscilloscope, it can detect the “flashover” phenomenon intuitively, accurately, quickly and reliably. When the electrical equipment under test has no "flashover" phenomenon, the oscilloscope will

3-30A Ground Resistance Tester for Testing Medical Equipment as IEC60601-1 1. Introduction RK7305Y medical grounding resistance tester is used to measure the ground (earth) resistance inside the electrical equipment, which reflects the (contact) resistance between the exposed conductive parts of the electrical equipment and the general grounding terminal of the electrical equipment. This equipment can meet the test requirements of IEC60335-1 and IEC60601. 2. Application 1).

Program-Controlled Leakage Current Tester for Testing Medical Equipment 1. Introduction RK7500Y series medical leakage current tester is a programmable and one-key serialization test equipment, built-in medical simulation human body network, it can perform ground leakage current, touch current, patient leakage current, patient auxiliary current and etc. tests as per IEC60601-1 and IEC61010-1. 2. Features 1). Built-in medical simulation human body network 2). It can synchroniz

Dielectric Strength Test Device with 30N Loaded Hardened Steel Pin IEC60335-1 clause 21.2 1. Introduction The dielectric strength test device is designed to meet the test requirements of IEC60335-1 clause 21.2, a hardened steel pin is used as a electrode during the dielectric strength test. After the scracth test, the device should work with a hipot tester to test the withstand dielectric strength of the accessible parts of the solid insulation. 2. Parameter Hardened steel

PLC Type Tracking Index Tester IEC60112 for Testing Proof amd Comparative Tracking Indexes 1. Introduction The tracking index test apparatus is controlled by 7-inch color touch screen and PLC. The test apparatus is built-in air exhaust, the front panel is transparent for easy observation of the experimental process. The tracking index test apparatus is designed according to IEC60112, UL746A, GB.T4207, GB4706.1 and TMD 3628-92. On the surface of the solid insulating material,

Multiplex Temperature Meter LCD Touch Screen Real-Time Display Multi-Point Temperature and Change Curves 1. Introduction of Multiplex Temperature Meter Multiplex temperature tester is a equipment that can simultaneously monitor multiple channel temperatures. Equip with 5-inch LCD touch screen, the upper and lower limit can be preset for alarming, display and record the temperature of each channel at real time, the column graph and temperature change graph can visually show

IEC60335-2-7 PLC Control Door and Interlock Endurance Testing Equipment for Washing Machine 1. Introduction Washing machine door endurance test machine can meet the requirement of IEC60335-2-7 clauses 18.101 and 22.104, IEC60335-2-11 clause 20.101 and IEC60335-2-4 clause 18, it is a special test equipment applied to life test of lid or door interlock of various washing machines and tensile force test when the interlock device acts to lock the door. The washing machine door

ISO11925-2 Building Material Flammability Tester PLC Control 1. Introduction The building material flammability tester is designed according to GB/T8626-2007 and ISO11925-2:2020 standards. In a normal combustion environment to assess the flammability of building products by direct impingement with a small flame on a vertically placed specimen. The device is controlled by PLC and touch screen, the combustion chamber is made of stainless steel sheet with a heat-resistant glazed

High Pressure Transparent Water Tank for IPX8 Testing and Leakage Detection 1. Introduction High pressure leak testing machine can meet the requirement of IEC60529 for IPX8 testing and IEC60598. The pressure in the jar can be precisely automatically controlled in purpose of checking the tightness and the leak points (by observe the bubbling during the test).The equipment is mainly consisted by transparent Sealed jar and control unit. 2. Features ● For IPX8 test. ● Working

6KV/500mA AC/DC Withstand Voltage Tester with Alarming Function 1. Introduction AC/DC withstand voltage tester (hipot tester) is a equipment to test dielectric strength, can accurate and fast to test break down voltage, leakage current and other electric safety index. It is meet the requirements of IEC60335, IEC60598-1, IEC60065 and IEC60950. 2. Features 1). The test voltage up to 5KV with DC and AC test function 2). The output voltage is adjusted by voltage regulator 3).

IEC60695-11-5 Electrical Safety Test Equipment Stainless Steel Needle Flame Tester 1. Introduction of Needle Flame Tester: ZY-2 Needle flame tester is designed according to IEC60695-11-5(IEC60695-2-2). It is applicable to ignition hazard test, combustibility test of electronic industry and home electronic appliance. The equipment specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess product and