Textile Test Equipment

EN 367 Heat Transfer Index Test Equipment Catalogs for EN 373&348&6942&367&702.pdf Introduction A new term heat transfer index (HTI) has been introduced to avoid confusion with the thermal protective index (TPI) or other terms used in previous versions of this test. HTI calculated from the mean time in seconds to achieve a temperature rise of 24±0.2℃ when testing by this method using a copper disc and a starting temperature of 25±5℃. The heat transfer index provides a method

Contact Heat Transmission Test Apparatus Catalogs for EN 373&348&6942&367&702.pdf Introduction Contact Heat Transmission Test Apparatus is applicable to protective clothing (including hand protectors) or its constituent materials intended to protect against high contact temperature. The application of the standard is restricted to contact temperatures from 100 °C to 500 °C.​ Feature The Contact Heat Transmission Test Apparatus is designed and manufactured according to EN 702

Protective Clothing Heat Radiation Resistant Test Equipment Catalogs for EN 373&348&6942&367&702.pdf Introduction It is suitable to determine heat radiation resistance or thermal conductivity of protective gloves and protective clothing. Feature 1. Radiation source is made up of 6 groups heating bar,length of heat bar is 356mm±2mm,and the length of heating part is 178±2mm,diameter of heating bar is 7.9±0.1mm. 2. Radiation source uses PID temperature controller,controlling

Molten Metal Splashes Impact Test Apparatus Catalogs for EN 373&348&6942&367&702.pdf Introduction Projections of molten metal drops at a point on a vertical oriented test specimen and measurement of the number of the drops required to cause a 40 K temperature rise in a sensor behind the specimen.​ Feature Drop guide to collect the drops and to guide them towards the vertically oriented test specimen. ​Senor for measuring the temperature linked to a recording device. ​This

ISO 9185 Molten Metal Splashes Resistant Test Equipment Catalogs for EN 373&348&6942&367&702.pdf Introduction It is suitable to measure the resistance of protective materials to liquid metal splash.During test,certain molten metal splashes on sample which is installed at specified angel.Put a PVC film on the sample’s back to contact it.Record the change of PVC film after splashing to evaluate the damage situation.According to test result,using bigger or smaller metal to

Protective Clothing Contact Heat Transmission Test Equipment Introduction: This contact heat transmission test Equipment is designed according to ISO12127-2007 and EN702. The tester uses the heating cylinder to provide a constant temperature in contact with the sample undercertainload and a calorimeter to measure the heat transfer properties. This contact heat transmission test equipment is easy to operate, the data is accurate, safe and reliable, widely used in fire

Standard: ISO 6530: 2005:Protective clothing - Protection against liquid chemicals - Test method for resistance of materials to penetration by liquids. Specification of AIC-6530 Liquid Penetration Test Equipment: 1. Test tank: semi-cylindrical, inner diameter (125±5) mm, length (300±2) mm, inclined 45°. 2. Syringe: specification (10±0.5) ml, needle hole diameter: (0.8±0.02) mm. 3. Automatic injection system, the syringe continuously sprays (10±0.5) ml test within (10±1) s to

Introduction: Protective Clothing Contact Heat Transmission Tester is applicable to protective clothing (including hand protectors) or its constituent materials intended to protect against high contact temperature. The application of the standard is restricted to contact temperatures from 100℃ to 500℃.​ Features: Protective Clothing Contact Heat Transmission Tester is designed and manufactured according to EN 702 and ISO 12127-1 standards. Protective Clothing Contact Heat

Product introduction Full Face Mask Flame Resistance Tester is suitable for testing the combustion resistance of self-contained open-circuit compressed air respirator (air respirator) in EN136 standard. The combustion performance of air respirator can be tested by means of 6-point burning or single-point burning flame impact.The flame retardancy tester is mainly used to test the flame retardancy of the comprehensive protective mask after six different parts of the flame

Full Face Masks Fire Heat Radiant Resistant Test Apparatus Introduction: Fireman fire protective clothing is mainly composed of jacket and bibcomposition,may also wear fire protective helmets, fire protective bootsandfire-protective gloves! Each set must be fitted a serial number of check marks given by national fire equipment quality inspection center to manufacture. Standards EN 136 - Respiratory protective devices - Full face masks - Requirements, testing and marking Main

Vertical Flame Spread Properties Test Equipment Introduction: Protective clothing flame spread properties test equipment is designed according to ISO 15025 . It can test the flame spread state under the small flame .It is used to simulate the protective clothing is at the risk of ignition to assume the flame spread performance .It is also suitable for the fabri cmaterial or other similar functional use of combustible materials . Standard BS EN ISO 15025:2016 specifies two

Introduction This Contact Heat Transmission Tester is designed according to EN702 standard,and it can meet requirements of Chinese standard AQ6103-2007 Protective gloves for welders.The test results includes contact temperature,time of starting test,threshold time etc. The principle is:under set contact temperature,the measuring protective fabric contacts heating column while bearing 49N pressure,the time of temperature raising 10℃ from initial temperature is threshold time

ISO 6942 Protective Clothing Heat Radiation Behavior Test Apparatus Introduction: This Heat Radiation Behavior Test Apparatus is designed according to ISO6942 and EN366 . The test apparatus has a user-friendly, intuitive, Windows-based application that provides a complete thermal control, fault detectionanddata recording. RPP system configuration and burn prediction also included in theThermDAC. User-defined test allows the operator to definea non-standardtest conditions and

EN 366 Protection Against Radiant Heat Test Equipment Introduction: This Protection Against Radiant Heat Test Equipment is designed according to ISO6942 and EN366 . The test equipment has a user-friendly, intuitive, Windows-based application that provides a complete thermal control, fault detectionanddata recording. RPP system configuration and burn prediction also included in theThermDAC. User-defined test allows the operator to definea non-standardtest conditions and custom

Introduction This flammability testing equipment is designed according to the latest edition of the national standard GB/T14645 design and manufacturing.It applies to textile fabric in under 45 ° combustion, determination of the damaged area and damage length determination of heat or melt number to provide exposure to the flame length. Combustion evaluation of refractory materials fire-resistant and can be based on compliance with the implementation of standards, measurement

Introduction: ASTM D6413 Vertical Flame Spread Test Equipment is for measuring the vertical flame spread for children's sleepwear, fabrics, other textile materials or resilient filling materials used in upholstered furniture. Meet CFR 1615/1616, ASTM D6413 and CALIF TB117.​ Features: ASTM D6413 Vertical Flame Spread Test Equipment uses stainless steel test cabinet with glass observation panel. Back wall painted black for easy test viewing. Specimen holders, burner and

Product introduction The Full Face Mask Thermal Radiation Test Equipment is suitable for testing the radiation resistance of full face mask respiratory protective devices in EN136 standard. Its purpose is to detect whether the mask will cause protection failure after being exposed to the standard heat radiation source after the standard test time. Full face masks for diving apparatuses are not included in the scope of this standard. Performance characteristics 1. The Full

Introduction: TheTextile Toys Flammability Test Equipment is used for the purposes of determining the flammability of toys under the particular test conditions specified. EN 71-2 includes general requirements relating to all toys and specific requirements and methods of test relating to the following toys, which are considered as being those presenting the greatest hazard: -toys to be worn on the head: beards, moustaches, wigs, etc. made from pile or flowing elements;masks;

IMO FTPC PART 7 Textiles and Films Fire Resistance Tester Introduction: This tester is designed according to IMO FTPC PART 7. It can test the flame spread state under the small flame . It is used to simulate the textiles and films under risk of ignition to assume the flame spread performance . It is also suitable for the fabric material or other similar functional use of combustible materials . Standard IMO FTPC PART 7 IMO RES.A 471 (XII) IMO RES.A 563 (14) Features: 1.The

ASTM F2100 Surgical Masks Flammability Testing Equipment Introduction This flammability testing equipment is designed according to the latest edition of the national standard GB/T14645 design and manufacturing.It applies to textile fabric in under 45 ° combustion, determination of the damaged area and damage length determination of heat or melt number to provide exposure to the flame length. Combustion evaluation of refractory materials fire-resistant and can be based on