Display Driver ICs

The MAX3232I is a multichannel RS-232 line driver/receiver operating from 3V to 5.5V. It features low 300 µA supply current, ±15 kV ESD protection, and supports data rates up to 250 kbit/s. Ideal for battery-powered systems, PDAs, and laptops. Available in multiple package options.

The ST485BD is a low power RS-485/RS-422 transceiver IC with 300µA quiescent current, operating from a single 5V supply. Features thermal shutdown, short-circuit protection, and supports up to 64 transceivers on the bus. Ideal for industrial multipoint data communication. Available in SO-8 package.

The ADM3078EARZ is a 3.3V RS-485/RS-422 transceiver with ±15kV ESD protection and 16Mbps data rate. Features true fail-safe receiver inputs, hot-swap capability, and supports up to 256 nodes. Ideal for industrial control, metering, and security systems.

The LAN8710A-EZC-TR is a high-performance 10/100 Ethernet transceiver with HP Auto-MDIX and flexPWR technology. It supports MII and RMII interfaces, operates from 1.6V to 3.6V, and comes in a compact 5x5mm RoHS-compliant QFN package. Ideal for set-top boxes, routers, and embedded telecom applications.

Quad push-pull driver delivering 1A per channel with 2A peak. Features TTL-compatible logic, inhibit input, separate logic supply, and overtemperature protection. Ideal for motor and relay control. Available in DIP-16 and DIP-20 packages.

80mΩ high-side MOSFET switch with 1000mA continuous current per channel. Features independent thermal and short-circuit protection, 8kV ESD protection, and undervoltage lockout. Ideal for capacitive loads and short circuits. Operating range 2.7V to 5.5V.

High-current MOSFET/IGBT driver with 10A peak output, matched 15ns rise/fall times, and low 1.2Ω output impedance. Latch-up protected, immune to ground bounce up to 5V. Ideal for motor drivers, pulse generators, and heavy line driving. Available in space-saving 8-pin DFN package.

Dual-channel smart high-side power switch with 105mOhm on-resistance per channel, supporting 7V to 58V operation. Features short-circuit, overload, and thermal protection with diagnostic feedback. Ideal for 12V/24V/42V automotive and industrial loads. Replaces relays and fuses.

High speed 0.4A peak output current IGBT/MOSFET gate drive optocoupler with 0.7µs propagation delay and 10kV/µs CMR. Wide operating voltage 10V-30V, temp range -40°C to 100°C. UL/CSA/IEC certified. Ideal for motor control inverters.

The A4982SLPTR-T is a complete microstepping motor driver with built-in translator, supporting full to 1/16-step modes. Features low RDS(ON) outputs, automatic decay mode, and overcurrent protection. Operates up to 35V and ±2A. Ideal for precise stepper motor control in industrial applications.

The SN65HVD485EDR is a 5V half-duplex RS-485 transceiver supporting data rates up to 10Mbps and up to 64 nodes per bus. Features 15kV ESD protection, bus-open-failsafe, and thermal shutdown. Ideal for industrial automation, motor control, and building networks. Available in MSOP-8 package.

The SN74LVC1G125 is a single bus buffer gate with 3-state output, operating from 1.65V to 5.5V. Features low power consumption (10-μA max ICC), 3.7 ns propagation delay at 3.3V, and ESD protection. Ideal for industrial and consumer electronics. Available in ultra-small packages.

High-performance octal buffer and line driver with 3-state outputs. Features PNP inputs for reduced DC loading, hysteresis for improved noise margins, and high sink-current capability. Ideal for bus lines and memory address registers. Reliable TI quality.

SN74LS07DR hex buffers/drivers with open-collector high-voltage outputs up to 30V. Features 40mA sink current, TTL-to-MOS level conversion, and input clamping diodes. Ideal for driving relays, lamps, and high-current loads. Compatible with most TTL families.

The L9822EPD is an octal low-side solenoid driver with eight 0.5 Ohm DMOS outputs, SPI control, and output diagnostics. Ideal for automotive lamps, relays, and solenoids. Features short-circuit protection, 36V clamping, and low quiescent current. Available in Multiwatt15 and PowerSO20 packages.

The MAX232EIDR is a dual RS-232 driver/receiver IC operating from a single 5V supply. Features ±30V input levels, low 8mA supply current, and ESD protection up to ±15kV. Ideal for reliable serial communication in industrial and commercial applications.

CD4050BM hex buffer IC operates from 3V to 15V, drives 2 TTL loads at 5V, and features high source/sink current. Ideal for CMOS to DTL/TTL conversion and logic level shifting. Reliable for industrial applications.

High-reliability CMOS 14-stage binary counter/divider IC. Features low power consumption, wide supply voltage range, and direct drive capability. Ideal for timing, frequency division, and industrial control applications. RoHS compliant.

Low-power RS-232 transceiver IC from Intersil, operating from 3V to 5.5V with 250kbps data rate. Features 15kV ESD protection, on-chip charge pumps, and automatic powerdown. Ideal for portable devices, laptops, and battery-powered equipment. Pb-free option available.

Low power RS-232 transceiver with 300 µA supply current, 400 kbps data rate, and dual drivers/receivers. Operates from 3V to 5.5V with true RS-232 performance. Ideal for battery-powered devices. Available in SO-16 and TSSOP-16 packages.