Bently Nevada Vibration Monitoring System

SICK INCREMENTAL ENCODERS DBS50E-S5CK01000 | DBS36/50 Product Specifications Attribute Value Pulses per revolution 1,000 Communication interface Incremental Number of signal channels 6-channel Supply voltage 7 ... 30 V Reference signal, number 1 Shaft material Stainless steel Product Description This product is a standard product and does not constitute a safety component as defined in the Machinery Directive. Calculation based on nominal load of components, average ambient

24765-01-00 Bently Nevada Case Expansion Transducer Systems Product Specifications Attribute Value Input Power +24 Vdc, 30 mA minimum Scale Factor 0.346 V/mm (8.79 V/in) Linear Range ± 12.7 mm (±0.5 in) Minimum Load Resistance 50 kΩ Length 241 mm (9.50 in) Weight 2.3 kg (5.0 lbs) Product Description An essential component in Turbine Supervisory Instrumentation (TSI), the Case Expansion Transducer System measures thermal growth of machine casings during startup and operation.

330450-20 330450-40 Bently Nevada High Temperature Acceleration System Product Specifications Sensitivity 10.2 mV/m/s2 (100 mV/g) ±5% Input Voltage -24 ± 0.5 Vdc Case material 300 series stainless steel Connector 3-pin Mil-C-5015 receptacle, hermetically-sealed, 304 stainless steel shell Weight 635 grams (1.40 lb)-794 grams (1.75 lb) Bend Radius Minimum bend radius of 51mm (2.0in) Product Description The standard 330400 Accelerometer has a limited temperature range due to its

Bently Nevada 3300 NSv Proximity Probe 330901 330905 Product Specifications Attribute Value Input Accepts one non-contacting 3300 RAM or 3300 NSv Proximity Probe and Extension Cable Power Requires -17.5 Vdc to -26 Vdc without barriers at 12 mA maximum consumption, -23 Vdc to -26 Vdc with barriers. Operation at a more positive voltage than -23.5 Vdc can result in reduced linear range Supply Sensitivity Less than 2 mV change in output voltage per volt change in input voltage

Bently Nevada Machinery Condition Monitoring 330400 Temperature Sensitivity -11% to 3% Product Specifications Attribute Value Sensitivity 10.2 mV/m/s2 (100 mV/g) ±5% Acceleration range 490 m/s2 (50 g) peak overall acceleration within the 10 Hz to 15 kHz frequency span. Vibration at frequencies above 15 kHz, especially at the transducers resonance will significantly decrease this range. Amplitude Linearity ±1% to 490 m/s2 (50 g) peak Broadband Noise Floor (10 Hz to 15 kHz) 0

Bently Nevada Machinery Condition Monitoring System 200350 High Efficiency Product Specifications Attribute Value Mounting Thread 1/4-28 Female Mounting Torque (Maximum) 2 to 5 ft-lb (2.7 to 6.8 N-m) Sensing Element Ceramic Sensing Geometry Shear Housing Material Stainless Steel Sealing Welded Hermetic Product Overview The 200350 and 200355 Accelerometers are general purpose, case-mounted seismic transducers designed for use with Trendmaster Pro Constant Current Direct Input

Bently Nevada 200155 Machinery Condition Monitoring Measurement Range in m/s² g ±196 ±20 Key Specifications Attribute Value Used with ProTIM Option Low Frequency Acceleration-to-Velocity channel type (-05) Type of Application Fin-Fan, slow rotating shafts Measurement Range in m/s² (g) ±196 (±20) Mounted Resonant Frequency >20 kHz (>1200 kcpm) Amplitude Linearity (1 to 10g pk) ±2% Transverse Sensitivity ≤7% Product Overview The Bently Nevada 20015x Accelerometers are general

Bently Nevada Accelerometer Interface Standard Cable 200152-25-10 USA Manufactured Product Specifications Attribute Value Part Number 200152-25-10 Model Number 200152-25-10 Manufacturer Bently Nevada Country of origin USA Weight 2kg Lead time 12-16 weeks Product Description The Bently Nevada 20015x Accelerometers are general purpose, wide frequency, case-mounted seismic transducers designed for use with Trendmaster ProTIMs. The 200150 Accelerometer also operates with the

Bently Nevada Accelerometer Interface Standard Cable 1.5kg Part Number 200151-020-03-02 Product Specifications Part Number 200151-020-03-02 Model Number 200151-020-03-02 Manufacturer Bently Nevada Country of Origin USA Weight 1.5kg Lead Time 12-16 weeks Product Description The Bently Nevada 20015x Accelerometers are general purpose, wide frequency, case-mounted seismic transducers designed for use with Trendmaster ProTIMs. The 200150 Accelerometer also operates with the

BENTLY NEVADA Cable Assembly Velomitor Right Angle 17FT 89477-17 Product Specifications Attribute Value Part Number 89477-17 Model Number 89477-17 Manufacturer Manufacturer Country of origin USA Weight 2kg Lead time 12-16 weeks Product Description The BENTLY NEVADA Cable Assembly Velomitor Right-Angle 17FT 89477-17 features: Two-conductor 18 AWG twisted, shielded cable Right angle two-socket plug at one end Terminal lugs at the other end Compatible with monitors and 21128

20kHz Bently Nevada Vibration Monitoring System 200150 200155 200157 AccelerometersTechnical SpecificationsAttributeValueSensitivity @ 80 Hz (± 12%)10.2 mV/(m/s2) (100 mV/g)Mounted Resonant Frequency>20 kHz (>1200 kcpm)Size17.5 mm x 45.7 mmWeight58 g (2.0 oz), typicalMounting Thread3/8-24 femaleMounting Torque2.7 to 6.8 N•m (2 to 5 ft•lbf)Sensing ElementCeramicSensing GeometryShearBently Nevada 200150, 200155 and 200157 AccelerometersThese general purpose, wide frequency,

Bently Nevada 165855 Cylinder Pressure Transducer Cylinder Pressure System Product Specifications Measurement Range 0 to 100/250/500/1000/2500/5000/10,000 psia0 to 6.8/17/34.5/69/172/345/689 bar Proof (Over) Pressure 1.5X Full Scale Burst Pressure 3X Full Scale (2X FS on 689 bar/10,000 psia units) Full Scale Output 10 ± 0.3 Vdc Zero 0.5 ± 0.1 Vdc Power Supply 18 to 30 Vdc Product Description The Bently Nevada 165855 Cylinder Pressure Transducer, when combined with the 146824

43501-01-04-01 Bently Nevada Low Pressure Cable Seal The 43501 Low Pressure Cable Seal provides a means to pass through a single hole in a machine case or other barrier one to four 95- ohm transducer cables or one to two 25mm DE and 50mm DE transducer cables. A molded silicone rubber grommet provides a seal to prevent leakage of fluids along the outer jacket of the cable(s). The seal mounts in a hole tapped with either ½-NPT or ¾-NPT pipe threads in the machine and has

Bently Nevada 3300 XL 11 mm Proximity Probes 330707 for Polyphenylene Sulfide PPS Tip Product Specifications Probe Tip Material Polyphenylene sulfide (PPS) Probe Case Material AISI 304 stainless steel (SST) Proximitor Sensor Material A380 aluminum System Length 5 or 9 extension meters cable Connector Material Gold-plated brass Maximum torque 0.565 N·m (5 in·lb) Product Description The 3300 XL 11 mm probe is available in multiple configurations, including armored and unarmored

Bently Nevada 991 Thrust Transmitter 23 mA Current Limiting Proximity Probe Compatible Product Specifications Attribute Value Input Accepts 1 non-contacting 3300 NSv Proximity Probe and extension cable. Power Requires +12 to +35 Vdc input at the transmitter terminal. 4 to 20 mA Signal Output 4 to 20 mAdc over specified full-scale range in 2-wire configuration. 4 to 20 mA Loop Accuracy Within ±1.5% over specified full scale range (typical). Accuracy is rated from the TEST

Bently Nevada 3300 XL 50 mm Proximity Probe 330876 with AISI 304 SST Case Product Attributes Attribute Value Probe Tip Material Polyphenylene Sulfide (PPS) Probe Case Material AISI 304 stainless steel (SST) Proximitor Sensor Material A380 aluminum Sliding Bracket Material Anodized aluminum and stainless steel System Length 5 or 9 metres including extension cable Probe and Extension Cable Armor (optional) Flexible SST with PFA outer jacket Product Description The 3300 XL 50 mm

Bently Nevada 9200 Seismoprobe Velocity Transducers Product Specifications Attribute Value Sensitivity 20 mV/mm/s (500 mV/in/s), ±5% when properly terminated and oriented at the angle of calibration. Calibration Load 10 kΩ Terminal "A" to "B" Output taken across pins "A" and "B" Sensitivity Temperature Coefficient 0.2%/°C Dynamic operating range 2.54 mm (0.100 in) peak to peak maximum displacement Velocity Range 25 mm/s (1 in/s) (at +22 °C of casing vibrat

Bently Nevada 330500 Velomitor Piezo-velocity Sensor Velocity Range 1270 mm/s 50 in/s peak Product Specifications Attribute Value Sensitivity 3.94mV/mm/s (100 mV/in/s) ±5%. Frequency Response 4.5 Hz to 5 kHz (270 cpm to 300 kcpm) ±3.0 dB. 6.0 Hz to 2.5 kHz (360 cpm to 150 kcpm) ±0.9 dB. Temperature Sensitivity -14% to +7.5% typical over the operating temperature range. Velocity Range 1270 mm/s (50 in/s) peak. Transverse Sensitivity Less than 5% of sensitivity. Amplitude

3300 XL 11 mm Proximity Transducer System 330704-000-060-10-02-00 Product Specifications Attribute Value Input Accepts one non-contacting 3300 XL 11 mm Proximity Probe and Extension Cable. Power Requires -17.5 Vdc to -26 Vdc without barriers at 12 mA maximum consumption, -23 Vdc to -26 Vdc with barriers. Operation at a more positive voltage than -23.5 Vdc can result in reduced linear range. Supply Sensitivity Less than 2 mV change in output voltage per volt change in input

50ohm Bently Vibration Monitoring System 330180-50-00 330180-50-CN 330180-51-00 Product Specifications Attribute Value Proximitor Sensor Input Accepts one non-contacting 3300-series 5 mm, 3300 XL 8 mm Proximity Probe and Extension Cable. Power Requires -17.5 Vdc to -26 Vdc when installed with nonincendive circuit connected per installation drawing 140979 at 12 mA maximum consumption, -23 Vdc to -26 Vdc with barriers. Operation at a more positive voltage than -23.5 Vdc can