Electrical Safety Test Equipment

IEC60335-1 Trihedral or Tetrahedron Temperature Rise Black Test Corner 1. Introduction The black test corner is designed according to IEC60335-1 chapter 11 “heating”. It is applied to provide a standard required conditions for temperature rising test of electric appliance.The Black Test Corner is used for the measurement of the temperature radiated by different equipment during the tests from heating and abnormal operation. One is designed and made with the intention of

Oil Type High Voltage Hipot Tester Electrical Testing Equipment with 10KVA 100KV 1. Introduction The oil type high voltage hipot tester consists of the control console and the YDJ (G) oil test transformer. The YDJ (G) type test transformer is produced based on the original similar products based on the "Test Transformer" standard of the Ministry of Mechanical and Electrical Technology. The TDM (G) type test transformer is based on the YDJ (G) series test transformer according

Stainless Steel Pressure Apparatus for E14 E27 E40 Lampholders IEC60238 Figure 9 1. Introduction The lamphoders pressure apparatus are designed accoding to IEC(BS EN)60238 clause 16.7 figure 9 and GB17935 clause 15.7 figure 9, it is applied to test the mechanical strength of external metal parts (out shell and dome) of metal lampholders, the various parts are tested on the complete lampholder. The pressure is applied on the two diameters at horizontal and vertical direction.

IEC60598-1 / IEC60884-1 1. Introduction The screwed glands torque test apparatus is designed according to IEC60598-1 clause 4.1.2.5, IEC60884-1, GB2099.1 clause 24.6 and GB7000.1 clause 4.12.5, it is applied to test the screwed glands against the torque strength. Screwed glands shall be fitted with a cylindrical metal rod having a diameter equal to the nearest whole number of millimeters below the internal diameter of the packing

Needle Flame Tester Electrical Instrument Test Equipment with 35mm length Burner and Black Background 1. Standard of Needle Flame Tester ZY-2 Needle flame tester is designed according to IEC60695-11-5 and IEC60695-2-2 standard. 2. Application of Needle Flame Tester It is applicable to ignition hazard test, combustibility test of electronic industry and home electronic appliance. The equipment specifies a needle-flame test to simulate the effect of a small flame which may

1. Introduction of Needle Flame Tester ZY-2 Needle flame tester is fully met the requirements of IEC60695-11-5 and IEC60695-2-2 standard. The test machine specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess product and material’s ignition risk and fire retardance by a simulation technique the fire.

UL2556 and UL94 Wire and Cable Horizontal and Vertical Flame Test Apparatus for VTM VW-1 and FT-2 Testing 1. Introduction Wire and cable flame test apparatus is designed according to UL94, UL1581 and UL2556, it is applied to test the resistance of a wire, cable or cord to the horizontal and vertical propagation of the flame (VTM, VW-1, FT-1 and FT-2 classifaction). The flammability test uses a bunsen burner of a specified size (inside diameter of 9.5±0.3mm, length of 100±10mm

IEC60335-1 clause 25.15 Power Cord Anchorage Pull Force and Torque Tester 1. Description The cord anchorage pull force and torque tester is designed according to the standards of IEC60598, IEC60335-1 clause 25.15, GB7000, GB2486 and etc., It is used to test tension and torque on the terminals of appliances provided with a supply cord and household appliances intended to be permanently connected to fixed wiring with flexible cords, it shall not be possible to push the cord

IEC60695-2-20 Hot Wire Ignition Test Apparatus /Fire Hazard Testing Equipment 1. Introduction The hot wire ignition test apparatus is designed according to the standards of IEC60950, IEC60695-2-20, UL60950, ASTMD3874 and etc.. The hot wire ignition test uses a heating wire of a specific size (Φ0.5 mm* 250 mm) and a specific material (Ni80/Cr20), after pre-annealing with specified heating power (0.26W/mm) and the specified time (8s~12s), the hot wire is wound five times on the

IEC60884-1 Clause 23.2 Power Cord Anchorage Torque Test Apparatus - Accredited by Third-Party Lab 1. Introduction The power cord anchorage torque test apparatus is designed according to IEC60884-1 clause 23.2 (table 18) and VDE0620 clause23.2(table18). It’s used to test the power cords and flexible cables of household appliance and similar appliance. The torque test shall be carried out after the completion of retention test. The flexible cable is subjected for 1 min to a

IEC60884-1 Figure 13 Socket-Outlet Lateral Strain Test Apparatus 1. Introduction This device is for checking the resistance to lateral strain for socket-outlet according to IEC60884-1 clause 13.14 / figure 13 and VDE0620, It is apply to test whether the socket-outlets having rating up to and including 16A and 250V will cause any damage in the standard sense when they are subjected to lateral stress by an appliance that is inserted into the socket. Each specimen is mounted on

Durable Push Button Type UL746A Tracking Index Test Apparatus 220V/50Hz 1. Introduction The tracking index test apparatus is controlled by single chip and push buttons. The test apparatus is built-in air exhaust, the exhaust fan automatically draws air when power on, and automatically run for 2 minutes when power off. The front panel is transparent for easy observation of the experimental process. The tracking index test apparatus is designed according to IEC60112, UL746A, GB

IEC60695 45 Degree Tilted Needle Flame Test Apparatus Fire Hazard Protection Testing Equipment 1. Introduction The Needle Flame Tester consists of a dia.0.9mm needle burner that tilts to 45 degree from the vertical and is fueled with butane gas. The fire hazard of the specimen is assessed by measuring the burning duration of the specimen, and any ignition of the wrapping tissue and white pine board below the specimen. Needle flame tester is designed according to IEC60695-11-5

IEC60695 GWFI / GWIT Glow Wire Test Apparatus Fire Hazard Safety Testing Equipment 1. Introduction The glow wire tester is designed according to IEC60695-2-10 t0 IEC60695-2-13, UL746A, IEC829, DIN695 and VDE0471. The specific material and sharp heating wire is heated to specific temperature (550 ℃~960 ℃) for 1 min by max current, then vertical burns the EUT with certain pressure (0.95N) for 30s, then check if the test specimen and bedding material are burning, and count the

0.1N.m to 0.425N.m Power Cord Anchorage Torque Test Equipment for Flexible Cable Conforms to IEC60884-1 and VDE0620 1. Introduction The power cord anchorage torque test apparatus is designed according to IEC60884-1 clause 23.2 (table 18) and VDE0620 clause23.2(table18). It’s used to test the power cords and flexible cables of household appliance and similar appliance. The torque test shall be carried out after the completion of retention test. The flexible cable is subjected

IEC60884-1 Table 18 Power Cord Anchorage Torque Test Apparatus with 100mm Torque Disk The power cord anchorage torque test apparatus is designed according to IEC60884-1 table 18 and GB2099-2008 clause 23.2 table 18. It’s used to test the power cords and cables for household appliances. Parameters: 1. Torque disk diameter: 100mm 2. Weight: equipped with 2N, 3N 5N, 7N, and 8.5N weight, each 1 piece, can realize 0.1 0.15, 0.25, 0.35 and 0425N.m torque. 3. Table 18 Torque test

IEC60335-2-14 1. Standard of Kettle Insert Withdraw Endurance Testing Machine: The Kettle Insert Withdraw Endurance Testing Machine is designed according to the standard of IEC60335-2-15:2005 clause 22.103, IEC60335-2-3 clause 22.105, IEC60335-2-14 clause 22.103, GB4706.30-2008 , GB4705.2-2007 , GB4706.19 etc. 2. Test Sample of Kettle Insert Withdraw Endurance Testing Machine: Cordless

IEC60335 PLC Washing Machine Door Endurance Testing Maching with 7 Inch Touch Screen 1. Standard of Washing Machine Door Endurance Testing Machine Designed according to IEC60335-1, IEC60335-2-7 and IEC60335-2-11 2. Application of Washing Machine Door Endurance Testing Machine Pulsator washing machine, Drum Washing Machine 3. Introduction of Washing Machine Door Endurance Testing Machine Washing machine door endurance test machine can meet the requirement of IEC60335-1,

Aluminum Sauce Pans for Gas Burners EN30-1-1 Annex C.1 with Lids 1. Introduction The Standard aluminum sauce Pans are designed according to EN30-1-1 Annex C.1 and table C.1. The test pans are made of commercial quality aluminum with density of 2700kg/m2, and use a tightening joint to secure the mercury thermometer with a through hole range of 3.0 mm -7.0 mm, the stir tray is made by aluminum plate with thickness 1mm. 2. Parameter Measured heat load/kW Pans designation /mm

Portable Built-In Sensor Push-Pull Force Meter 50N/100N/200N/500N/1KN Range Optional 1. Features 1). High accuracy and resolution 2). Peak hold function 3). Peak automatic clearance function (1-9 seconds) 4). Tolerance limit (upper and lower limit) 5). Light for judging qualified and unqualified value 6). Long stand-by time and utility time, with lithium battery and low power chip 7). 30 memory data for calculate the average, max, min value 8). Automatic power off function (0