Electrical Safety Test Equipment

IEC62560 Bending Moment Test Device for Testing the Lamp at Lampholder 1. Introduction The bending moment test device is applied to test the bending moment of the lamp at the lampholders, the value of bending moment shall not exceed the values given in below table. The test device can meet the test requirement of IEC60968-2015-02 clause 6.2 and IEC62560 clause 6.2. Caps Bending moment (Nm) Mass (kg) B15d 1 / B22d 2 1 E11 0.5 / E12 0.5 / E14 1 / E17 1 / E26 2 / E27 2 1 E39 1 /

IEC60598-2-20 Figure Lampholder Contacts Security Test Device for Testing Lighting Chain 1. Introduction The lighting chains pressure test device is designed according to IEC60598-2-20 clause 20.12.4 figure 2 and GB7000.9 clause 11.3 figure 2. It’s applied for checking security of lampholder contacts in push-in lampholder of the lighting chains, to avoid the displacement of lampholder contacts due to friction, so that the live part of the lighting chains become accessible. 2.

IEC60236-1 Handle Lifting and Carrying Strength Test Equipment for Medical Equipment 1. Introduction The handle strength test apparatus is designed to meet the test requirement of to IEC60236-1-2018 clause 8.8, GB9706.1-2007 clause 21. It’s applied to test the strength of handle for lifting or carrying the equipment, like of portable medical equipment. A weight exerts a force of 3 times or 2 times the weight of the equipment shall be uniformly applied over a 75mm width at the

IEC60587 High Voltage Tracking Test Apparatus for Tracking and Erosion Tests 1. Introduction The high voltage tracking test apparatus is applied to tracking and erosion tests for insulating material of electronics products and household appliance according to IEC60587. The test uses liquid contaminants and inclined specimen to evaluate the resistance to tracking and corrosion of electrical insulating materials under severe ambient conditions at power frequency (48Hz-62Hz).

Interior Material of Vehicle Horizontal Flammability Test Equipment FMVSS302 1. Introduction Interior material of vehicle horizontal flammability test apparatus can meet the requirement of FMVSS302-2016, GB8410, DIN7520, GM6090M and GM9070P. The test apparatus is applied to evaluate horizontal burn resistance for material used in occupant compartments of motor vehicles (like cars, multipurpose passenger vehicles, trucks and buses), The interior material includes Seat cushions

Cold Bend Test Apparatus IEC60811-1-4 for Cable Made by SUS304 Stainless Steel 1. Introduction The cold bend test apparatus is designed according to IEC60811-1-4 clause 8.1 and figure 1, IEC60884-1, VDE0472, GB2951.4 and GB2099-94. It is applied to the test the cores of circular cross-section having an external diameter up to and including 12.5mm, sector shaped cores when it is not possible to prepare dumb-bells, and cables with an overall diameter up to and including 12.5mm

ESD-2000 EMC Test Equipment for Electrostatic Immunity Test IEC61000-4-2 Diode Display 1. Introduction: The ESD simulator is also known as ESD gun, it is a hand-held unit used to test the immunity of devices to electrostatic discharge (ESD) according to the standard IEC61000-4-2. The ESD simulator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. Electrostatic discharge generator is widely apply to the fields of industry

AC and DC Dielectric Withstand Tester 5KV / 10KV / 20KV / 50KV with CE Certificatet Introduction:Withstand voltage tester is also be called as hipot tester, dielectric withstand tester, high voltage tester, a specified AC or DC high voltage is applied between the live part of the appliance and the non-charged part (generally the outer casing) to check the ability of the electrical insulating material to against the high voltage, the voltage applied will only produce a small

Multiplex Temperature Tester with K Type Thermocouples 8 to 64 channels 1. Introduction Multiplex Temperature tester is an equipment to monitor multipoint temperatutre at real time, equip with software can record the temperature rising curve, which is easy to save and analysis the data. And the equipment has a supper big LCD display and U-disk interface, user can output the data by U disk. Multiplex temperature tester is a necessary equipment for temperaure rising test. 2.

Insulation Resistance and Withstand Voltage Tester 2 in 1 Eletrical Safety Test Equipment Introduction: Insulation and withstand voltage tester is a kind of electric safety test equipment, widely used in the fields of transformer, equipment, components and etc. to test the performance of insulation and withstand voltage. The equipment can give an alarm at current and resistance, and have 5 groups memories. Parameter: Model RK7112 RK7110 RK7122 RK7120 Test voltage AC:0~5KV AC

500VA Electrical Safety Test Equipment 250V Leakage Current Tester 1. Introduction RK2675 series leakage current tester is applied to test the leakage current caused by power supply, it's an important index to judge the quality of electronic appliance. Leakage current tester is widely used in household appliance, compressor, motor, cable and etc. RK2675 series tester has the alarming function, and the test time and value can be preset. 2. Parameters: Model RK2675S RK2675A

ISO 6722-1 Figure 6 Sandpaper Abrasion Test Apparatus for Testing Cable of Car 1. Introduction The auto cable sandpaper abrasion test apparatus meets the requirements of ISO6722-1 clause 5.12.4.1 figure 6, GB/T25085, QC/T730, JASO D608, JASO D611, SAE J1127, SAE J1128 and JIS C3406 standard. It’s applied for verify that the resistance of the cable insulation to sandpaper abrasion. Measure the “resistance to sandpaper abrasion” using 150J garnet sandpaper tape with 5mm to 10mm

IEC60335-1 IEC60065 Automatic Inclined Plane Device 0~45 Degrees tilted for Household Appliance 1. Introduction Inclined plane device is also called as electrical stability tester, it is conforms to the standards IEC60335-1 clause 20.1, IEC60065 clause 19.1, IEC60950 clause 4.1.1 and etc.. Inclined plane device is used to test the stablity perfomance of household and similar electrical appliances which used on a table or on the floor rotating at a certain angle of inclination

Temperature Rise Black Test Corner with 136 measurement Points (IEC60335-1 / Clause 11) 1. Introduction The Black Test Corner is used for the measurement of the temperature radiated by different equipment during the tests from heating and abnormal operation. One is designed and made with the intention of determining the fulfillment of different standards as far as the registry from temperatures during the operation of the apparatus under test. The Black Test Corner is

IEC60598 Electrical Safety Test Equipment Black Rectangular Draught - Proof Enclosure 1. Introduction Draught-proof enclosure is designed according to IEC60598.1 annex D, it is applied to thermal test of luminaire under the conditions of normal operation and abnormal operation. The draught-proof enclosure is rectangular, with a double skin on top and on at least three side, and with a solid base. The double skins are of perforated metal, spaced approximately 150mm apart, with

IEC60065 Electrical Safety Test Equipment Dielectric Strengt Test Instrument 1. Application: The equipment is designed according to IEC60065 and UL1310, It’s mainly used for testing thin-layer insulation material electric strength. Stand part of the test device using the whole structure, made of 304 plate material processing. To improve the insulation board and creepage dielectric properties, surface brushed polished, bottom bracket the minimum distance from the edge of >35mm

PLC Control Power Cord Flexing Test Equipment According To IEC60335-1 1. Introduction of Flexing Test Equipment Power cord flexing test apparatus is designed according to IEC60335-1 clause 25.14 and figure 8, IEC60335-2-14 clause 25.14, IEC60884-1 clause 23.4 and figure 21, AS/NZS3112 clause 2.13.12.2 and figure 2.2, BS1363-1 clause 19.5 and figure 18. It is widely used in power cord bending and swing testing on power cords, plugs and sockets, lamps, home appliances, IT/AV

IEC60695-11-5 Needle Flame Test Apparatus Electrical Safety Test Equipment 1. Introduction of Needle Flame Test Apparatus: ZY-2 Needle flame tester is designed according to IEC60695-11-5(IEC60695-2-2). It is applicable to ignition hazard test, combustibility test of electronic industry and home electronic appliance. The equipment specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess product and

Multiplex Temperature Meter LCD Touch Screen Real-Time Display Multi-Point Temperature and Change Curves 1. Introduction Multiplex temperature tester is a equipment that can simultaneously monitor multiple channel temperatures. Equip with 5-inch LCD touch screen, the upper and lower limit can be preset for alarming, display and record the temperature of each channel at real time, the column graph and temperature change graph can visually show the temperature change of each

Bending Test Equipment for Adjusting Luminaire Conforms to IEC60598-1 Clause 4.14.3 1. Introduction The bending test equipment for adjusting luminaire is designed to meet the test requirement of IEC60598-1 clause 4.14.3. The flexible cord or cable of adjusting luminaire shall have no more than 50% of the strands in a conductor be broken and no serious damage to the insulation after continuously bending and torsion. 2. Parameter Control mode PLC control+touch screen interface