Hammer Union Seal

2 Inch FKM Hammer Union Replacement Seal Rings for Figure 607 Guiberson Product Photo Product Specification Nominal 2-inch FKM hammer union replacement seal rings are specified for the identified Figure 607 Guiberson connection. Confirm the seal inside diameter, outside diameter, height and lip profile against the manufacturer part drawing. The 2-inch designation refers to the nominal connection size; it does not define the actual rubber ring dimensions or guarantee

Product Introduction Nominal 2-inch hammer union replacement seals for Figure 602 or Figure 1502 connections are specified as separately matched parts. Identify the union manufacturer and figure number, then confirm the seal lip section, inside and outside diameters, height and backing configuration. NBR, HNBR and FKM are separate compound options selected for the actual fluid and temperature service. Product Specification 1. Pressure specification: Confirm operating pressure

Hammer Union Seal Introduction Hammer union seals are replaceable elastomeric components fitted inside specified hammer union connections on oilfield pipework. Match the union figure, nominal connection size and seal profile before ordering. NBR, HNBR and FKM options must be selected for the fluid and service conditions; the seal alone does not establish the pressure rating of the connection. Product Specification 1. Connection matching: Figure 602, 1002 and 1502 identify

Rubber Seal Ring Buna FKM HNBR Weco FMC 3 Inch Wing Union Hammer Seals Nominal 3-inch wing union hammer seals are replacement rings for the identified pipe connection. For a WECO/FMC-referenced union, provide the manufacturer, figure number and part drawing. Confirm the actual ring dimensions and lip or O-ring profile; nominal connection size alone does not establish interchangeability. Buna-N (NBR), FKM and HNBR are separate compound options. Select hardness and any brass or

Standard Fig 602, 1002, 1502 Hammer Union Seals for Sale NBR HNBR FKM PTFE Product Introduction High-performance Hammer Union Seals (also known as lip seals) are replacement components for specified hammer union pipe connections. Identify the union manufacturer, figure and nominal size, then match the seal profile to the approved drawing or sample. Figure 602, 1002 and 1502 are connection identifiers; the figure number alone does not confirm interchangeability or the rating

Product Introduction These FKM hammer union lip seals are specified for the actual union manufacturer, figure, nominal size and groove. Match the lip profile and backup arrangement to the original component drawing. Review the supplied compound against the fluid and operating conditions; complete-union documentation determines pressure and service acceptance. Product Specification Material Properties FKM (fluorocarbon) is the material family listed for this lip seal. Specify

Product Description: HNBR hammer union seals are reviewed for the specified union figure, nominal connection size and part drawing. Confirm the rubber lip profile and any brass backup construction against the mating hardware before replacement fit is approved. Specify compound, nominal Shore A hardness and tolerances for the actual fluid and temperature exposure. Sour-gas suitability requires qualified material and assembly acceptance; hardness alone does not establish

1, 2, 3 and 4-Inch Hammer Union Seal Enquiries — Custom Profile and Material Approval Product Introduction Hammer Union Seals are used in the connections between flexible hoses or pipes used in the oil drilling industry. The seal provides a critical fluid tight connection within the union hardware. Hammer Unions consist of a thread end, a nut end, and a hammer nut that when tightened seal the assembly with the assistance of an elastomeric seal. The seal is lipped to prevent

Brass-Backed Hammer Union Seals for FIG 602 and FIG 1002 Royal Way® brass-backed hammer union seal enquiries are matched to the specific FIG 602 or FIG 1002 assembly drawing. Specify the elastomer compound, brass component geometry and union manufacturer together. Confirm whether the order covers the complete specified construction or individual replacement parts. The brass-backed construction must be reviewed with the union seal pocket and operating conditions. Provide fluid

Product Description: This NBR rubber hammer union seal is supplied for the specified union figure and nominal connection size. Confirm the finished seal profile, dimensions and compound limits for the intended temperature and fluid exposure. Pressure capability must be assessed for the complete union assembly and its operating conditions. For a Weco-pattern replacement, provide the exact union figure, size, part reference and drawing or sample. Check the sealing interface and

2 to 4-Inch Figure 1502 Hammer Union Seals — Brass Backup Geometry and Compound Selection Product Introduction Hammer Union Seals are used in the connections between flexible hoses or pipes used in the oil drilling industry. The seal provides a critical fluid tight connection within the union hardware. Hammer Unions consist of a thread end, a nut end, and a hammer nut that when tightened seal the assembly with the assistance of an elastomeric seal. The seal is lipped to

2, 3 and 4-Inch Buna Hammer Union Seals with Stainless Steel Backing Buna (NBR) union seals with stainless steel backing are specified by the union groove and backup-ring geometry. For 2, 3 or 4-inch connection enquiries, provide the figure number and mating drawing. The metal backing supports the specified seal construction; it does not establish an independent pressure rating. Each union figure requires its own groove and seal profile. Confirm the required lip seal or O

4-Inch Nitrile 80 Shore A Hammer Union Lip Seal with Stainless Steel Backing This lip seal is specified for a 4-inch nominal hammer union connection, using nitrile (NBR/Buna-N) rubber at nominal 80 Shore A with stainless steel backing. The lip provides contact with the union seat; the backing supports the rubber at the designed extrusion clearance. Match both components to the exact union figure and manufacturer drawing. A 4-inch connection designation does not define the

Hammer Union Lip Seals — Rubber-Only and Metal-Backed Selection Select a replacement lip seal by union figure, nominal size, mating groove drawing and construction. The listed Buna and FKM rubber-only seals and brass or stainless steel backed options require their own fit checks. Include fluid formulation, temperature, pressure cycles and decompression conditions when specifying the compound. Product Specification 1. Pressure selection: Union figures identify connection

Custom Figure 602/1002/1502/2002/2202 Hammer Union Seals: Direct Factory Supply for Oil & Gas High-Performance Sealing Solutions for Oilfield Flowlines Hammer Union Seals, also commonly known as Lip Seals, are specialized elastomeric seals used in high-pressure piping systems within the oil and gas industry. Match the replacement seal to the actual union manufacturer, figure, nominal size and groove for fracturing, cementing or acidizing service. As a premier ISO 9001

Figure 602, 1002 and 1502 Hammer Union Seals — Material and Backup-Ring Orders Product Introduction Hammer Union Seals are used in the connections between flexible hoses or pipes used in the oil drilling industry. The seal provides a critical fluid tight connection within the union hardware. Hammer Unions consist of a thread end, a nut end, and a hammer nut that when tightened seal the assembly with the assistance of an elastomeric seal. The seal is lipped to prevent it from

NBR or FKM 2 Inch Figure 607 Hammer Union Replacement Seals for Hot-Oil Enquiries Product Photo Product Specification Nominal 2-inch Figure 607 hammer union replacement seals are specified in NBR or FKM for the identified hot-oil line connection. Match the seal profile, inside diameter, outside diameter, height and backing arrangement to the union manufacturer part drawing. Specify the compound separately from the nominal connection size; the same-size NBR and FKM options

2-Inch Figure 607 FKM Union Seal — Service-Life Selection Factors Other types For a nominal 2-inch Figure 607 Guiberson style FKM replacement, review the exact compound with the fluid formulation and operating cycle. Service life depends on compatibility, temperature, pressure cycling and groove condition. Specify performance and inspection requirements rather than assuming a fixed life from the FKM name. Confirm the Figure 607 groove and lip profile from the equipment

HNBR Hammer Union Seal Introduction Hammer union seals are replacement elastomeric parts fitted to specified pipe connections in oilfield service. This enquiry covers HNBR options alongside the listed NBR and FKM alternatives. Match the manufacturer, union figure, nominal size and seal profile before selecting a compound. The complete union assembly determines the connection rating. Product Specification HNBR union seal enquiries: compound and assembly requirements Provide

Product Description: Royal Way supplies NBR rubber hammer union seals with FKM and HNBR options available for separate material selection. The existing nominal union range is 1, 1.5, 2, 3 and 4 inches. Identify the original union maker, figure and seal drawing before ordering; nominal connection sizes do not establish finished seal dimensions. Temperature capability belongs to the selected compound and service conditions. Specify the continuous and peak temperatures, exposure