Flammability Test Equipment

Introduction: This Flooring Radiant Panel Tester is the cornerstone of the flooring materials reaction to fire tests in the Euroclass system. The test measures the spread of flame of the sample, under thermal exposure, using a radiant heat ignition source. The thermal exposure is that of a fire growing in the room of origin that through a door opening, radiates onto the floorings in an adjacent room or corridor. This Flooring Radiant Panel Tester an also be used for tests to

INTRODUCTION BS 476 part 6 specifies a method of test, the result being expressed as a fire propagation index, that provides a comparative measure of the contribution to the growth of fire made by an essentially flat material, composite or assembly. It is primarily intended for the assessment of the performance of internal wall and ceiling linings.​ FEATURE Prompted software interface Data recording and display of cowl temperature against time Data recording and display of

Glow Wire Flammability Index Test Machine Introduction: This Glow Wire Flammability Index Test Machine is designed according to IEC60695-2-10: 2000 standard "glowing filament test method". It is applicable to electrical and electronic products, household appliances and materials fire hazard testing, simulate burning elements or overload resistance and the like heat or ignition source thermal stress caused by a short time. Glow Wire Flammability Index Test Machine adopts

Fire Resistance Test Equpiment for Valve, Hose & Pipes Introduction: This fire resistance test equipment complies with the following standards: • Valve Fire Test (ISO 10497) • Fire Test hoses (ISO 19921 & 19922) • Plastic Pipe Fire Test (FTP II Res A 753) In the case of internal pressure, valves using a burner simulation of fire, for marine and similar joints of pipe and fire resistance test under load conditions. Several nominal diameter hose arrangement and plastic

45 ° Flammability of Wearing Apparel Apparatus Introduction This 45 ° Flammability Apparatus is designed according to the latest edition of the national standard GB/T14645 design and manufacturing.It applies to textile fabric in under 45 ° combustion, determination of the damaged area and damage length determination of heat or melt number to provide exposure to the flame length. Combustion evaluation of refractory materials fire-resistant and can be based on compliance with

Steiner Tunnel Furnace Introduction UL910 covers the test method for determining values of flame-propagation distance and optical smoke density for electrical and optical-fiber cables that are intended to be installed in ducts, plenums, and other spaces used to transport environmental air without the cables being enclosed in raceways in those spaces. The purpose of this test is to determine whether the flame-propagation and smoke-generating characteristics of cables without

EN ISO 1716 Bomb Calorimeter for Building Products OBC-B bomb calorimeter.pdf I. Introduction: 1. The bomb calorimeter automatically records the data of temperature and time. 2.Based on the input heat capacity, sample quality and additional heat and related data, it can automatically fulfil temperature correction and gross heat of combustion calculation, and give the results. 3.Gross heat of combustion and net heat of combustion can read directly,without calculation; 4.The

BS 476-15,ISO5660,ASTM E1354 Cone Calorimeter TCCT Cone Calorimeter.pdf Introduction: Heat release quantity is the core parameters to evaluate the fire behavior of materials and products.Our Cone Calorimeter can meet all existing standards (including ISO 5660, ASTM E 1354, ASTM E 1474, ASTM E 1740, ASTM F 1550, ASTM D 6113,NFPA 264,CAN ULC 135 and BS 476 Part 15).This cone calorimeter includes these systems such as heat release, mass loss, smoke generation, etc,and allow

EN 366 Radiant Heat Resistant Test Equipment Catalogs for EN 373&348&6942&367&702.pdf Introduction It is suitable to determine heat radiation resistance or thermal conductivity of protective gloves and protective clothing. Feature 1. Radiation source is made up of 6 groups heating bar,length of heat bar is 356mm±2mm,and the length of heating part is 178±2mm,diameter of heating bar is 7.9±0.1mm. 2. Radiation source uses PID temperature controller,controlling accuracy is ±1℃. 3

Catalogs for EN 373&348&6942&367&702.pdf Introduction The Molten Metal Splashes Impact Test Equipment is designed according to EN348 and ISO 9150,and it can meet requirements of Chinese standard GB8965.2-2009 “Protective clothing for welders” and GB/T 17599-1998 “Determination of behaviour of materials on impact of small splashes of molten meta”. Projections of molten metal drops at a point on a vertical oriented test specimen and measurement of the number of the drops

Catalogs for EN 373&348&6942&367&702.pdf Description: Molten metal small splashes impact tester is professional designed to evaluate the behavior of materials used for protective clothing of EN ISO 11611, EN ISO 20349 when such materials are struck by small liquid metal splashes which is designed according to EN 348 and ISO 9150. It is used to determine the protective performance of PPE (personal protective equipment) for wearer against small splashes of molten metal is often

Catalogs for EN 373&348&6942&367&702.pdf Introduction: A new term heat transfer index (HTI) has been introduced to avoid confusion with the thermal protective index (TPI) or other terms used in previous versions of this test. HTI calculated from the mean time in seconds to achieve a temperature rise of 24±0.2℃ when testing by this method using a copper disc and a starting temperature of 25±5℃. Heat Transmission on Exposure to Flame Tester is used to determine the heat

Introduction By configuring different test devices, many aviation fuel combustion test standards can be met, such as seat combustion test, burnthrough test of heat and sound insulation materials,flame penetration test of cargo tank lining, fire test of soft and hard pipe components, electric engine devices and electrical connectors, etc. The standards that can be met are FAR25.853,FAR 25.855, FARs25.855, FARs25.863, FARs25.867, etc. Meanwhile, it can meet the domestic MHT

Introduction: This Flammability Test Equipment is a multi-functional combined test bench, which can realize the combustion test of large combustible gas burners and small gas burners for the airborne equipment, accessories and components in the designated fire zone of aircraft. The test samples include cables and electrical connectors, hoses and pneumatic components. Standard: FAR 25.853 Part II,III,VII Features 1.The burner consists of elliptical combustion nozzle, igniter,