Oil Test Equipment

Four Ball Machine for Wear Preventive Characteristics Testing of Lubricating Grease Introduction This four ball test machine uses four Ф12.7mm standard steel balls evaluate the load-bearing capacity and anti-wear performanceof lubricants (including oil film strength PB, sintering load PD, comprehensive wear value ZMZ, Long-term wear D and other indexes). The influence of temperature on the lubricating performance of lubricants can also be measured. Main Features: 1.Adopting

Automatic RPVOT Rotary Pressure Vessel Oxidation Stability Tester RPVOT: The Rotary Pressure Vessel Oxidation Stability Tester is designed and made as per industrial standard of People’s Republic of China SH/T 0193 Lubricating oils-Determination of oxidation stability-Rotating pressure vessel method and ASTM D2272 Standard test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel. The instrument is used to determine the oxidation stability of steam

ASTM D4530 MCRT Micro Carbon Residue Tester Introduction The measurement range of this carbon residue tester is 0.10%(m/m)～30.0%(m/m). The test result is equivalent to Conradson method.It can also be used to determine the petroleum products composed of distillate oils which carbon residue is lower than 0.10%(m/m). Designed according to GB/T17144,the whole working process is automatic:raising temperature,automatic display,automatic timing,automatic switch and control

ISO 13736 Automatic Abel Closed Cup Flash Point Tester Introduction This Abel Closed-cup Flash Point Tester is our new product,which is strictly designed with different test modes for different test standards.It can test many items and automation degree is very high.It can be widely used for many industries,such as chemicals safety inspecting,petro-chemical inspection and plastic. I.Main features Test model options:it's strictly operated as per different standards of Abel

Cloud Point and Crystallizing Point Test Instrument Main features This test instrument is refrigerated by double air compressor with environment-friendly refrigerant.The cooling speed is fast. Not using traditional electromagnetic stirring,it is replaced with imported motor,0~80rmin adjustable. Special pilot crystalline hole guarantees the accuracy of experiment. Dewar bottle is cooling bath,which has good performance of thermal insulation. It’s made by cold-rolled steel

Manual Aniline Point Test Instrument Summary This instrument is suitable for the determination of aniline point of petroleum products by placing a specified volume of aniline and sample in a test tube and mixing it with mechanical agitation. The mixture is heated at a controlled rate until the two phases are completely mixed. The mixture is then cooled at a controlled rate, and when the two phases are separated, the recorded temperature is the aniline point. I. Main technical

High Frequency Reciprocating Rig Summary All diesel fuel injection equipment uses diesel as a lubricant to some extent. Excessive friction causes wear and tear to shorten the life of engine components such as diesel fuel injection pumps and fuel injectors. Diesel lubrication is one of the reasons. The experimental results of High Frequency Reciprocating Rig have a good correlation with the lubrication problems of diesel and related equipment, and can properly predict the

Percent Ash Content Tester for Engine Coolants and Antirusts Introduction The test principle of the percent ash content tester is to let the sample evaporation or burning under certain conditions,and put it in a strong heat source burning and ashing, then calcine the solid residue,then it can test the ash content of the test product. The percent ash content tester is suitable for the detection of unused commodity engine coolant and liquid antirusts. It can also used to

Introduction This Transformer Oil Breakdown Voltage Tester is developed according to the national standard IEC156 Insulating Oil Dielectric Strength Testing Method.It has large LCD display, micro-printer and can store 100 groups data. This Transformer Oil Breakdown Voltage Tester is multi-functional, stable, and easy for operation. ​ Functions: Breakdown test of user-defined Proof test IEC60156/IS6792/BS5874 test ASTM D1816 standard test ASTM D877 standard test 5 minutes

Fully Automatic Cleveland Open Cup Flash Point Analyzer ASTM D92 Automatic Open Cup Flash Point Test Instrument According to test method of GB/T3536,this open cup flash point test instrument adopts advanced Microprocessor and PID temperature controlling technology, the temperature rising speed is fast,temperature controlling is more precise, and test result is more accurate.LCD big screen replaces old design of RS323 port, the operation is easier. This COC-H5 automatic open

Introduction This test method covers a laboratory screening procedure for evaluating the effectiveness of engine coolants in combating corrosion of aluminum casting alloys under heat-transfer conditions that may be present in aluminum cylinder head engines. Characteristic 1. The Cast Aluminum Alloys Corrosion Tester consists of a support and one or two thermal corrosion cell, with a working pressure of 40 psi and a working temperature up to 160℃.Electronic timer controls

Summary The Fully Automatic Kinematic Viscometer is designed and made as per national standard of People's Republic of China GB/T 265 Petroleum products-Determination of kinematic viscosity and calculation of dynamic viscosity and GB/T1632-93 Test Methods for Viscosity Number and Limiting Viscosity Number of Polymers in Dilute Solution. The Automated Kinematic Viscosity Meter is suitable to determine Kinematic viscosity, viscosity number, and limiting viscosity number of oils

Introduction: This Thermal Stability Tester is suitable for testing the stability of Unused mineral oil and synthetic hydrocarbon heat transfer fluids. The use method is as follows: under a certain test temperature, heat the sample in isolation from the air for a specified time, then observe and record its appearance, calculate the quality of gas-phase decomposition products, conduct gas chromatographic analysis on the samples before and after heating, determine the content

Introduction The panel coking tester determines the tendency of finished oils to form coke when in contact with surfaces at elevated temperatures for short periods. A sample of oil is mechanically splashed against an aluminum test panel at elevated temperature. After a specified test period, the amount of coke deposited on the panel is determined by weight. Feature 1.The digitally controlled panel coking tester is suitable for finished lubricating oil. 2.The digital display

I.Lubricant Sulfated Ash Tester ASTM D874, GOST 12417, ISO3987 A new type of ceramic furnace is used as the heating body, which has a beautiful appearance and is suitable for detecting the ash content of sulfate in the lubricating oil containing additives and the additive concentrate of the blending lubricating oil. The lower limit for the instrumental determination of sulfated ash is 0.005%. II. Main features 1. Hot ceramic furnace, good heat preservation effect, avoid burns

I.ASTM D2783 Lubricating Grease Four Ball Wear Test Machine This 4 ball test machine uses four Φ12.7mm standard steel balls evaluate the load-bearing capacity and anti-wear performanceof lubricants (including oil film strength PB, sintering load PD, comprehensive wear value ZMZ, Long-term wear D and other indexes).The influence of temperature on the lubricating performance of lubricants can also be measured. II. Main features 1.Adopting double floating bearing technology, no

I.Over Wide Temperature Range Dropping Point of Lubricating Grease Tester ASTM D2265, ISO6299 This Dropping point test set is suitable for measuring the dropping point of lubricating grease in a wide temperature range. II. Main features 1. Microcomputer temperature controller, digital display, accuracy ±0.1℃, PT100 sensor;2. Six holes can be tested at the same time;3. Metal bath heating, safe and environmentally friendly;4. Chrome-plated brass cup, in line with ASTM standard

I.Timken Ring-Block Wear Test Machine ASTM D2782,ASTM D2509 This machine is mainly applied for simulating evaluation for kinds of lubricant, grease's extreme compression capacity and anti-confusion capacity. It can also be used for performance study of anti-friction capacity of aviation kerosene and capacities of all sorts of paint coating, metal and non-metal materials. II. Main features The Tester is made up of a 1.5 kw (0-1500r/Min) Servo motor, a digital speed indicator,

I.Lubricating Grease Relative Viscosity Tester This Lubricating Grease Relative Viscosity Tester adopts the automatic capillary viscometer method to measure the apparent viscosity of samples, and it is applicable to the testing of lubricating greases. II. Main features 1. Capillary viscometer with reasonable and compact structure;2. The magnetic circulating pump transmits the medium without noise;3. Stainless steel medium bath body;4. Microcomputer temperature controller,

I. Shear Stability of Polymer Containing Fluids Tester (Diesel Fuel Injector Nozzles) ASTM D6278 The Shear Stability of Polymer Containing Fluids Tester is a new high-tech product developed with German technology. It is suitable for the shear stability determination of polymer oil. The main engine consists of a double-piston jet pump and an atomization chamber with a nozzle and a nozzle bracket. It contains polymer At a certain shear rate, the oil passes through the diesel