Oil Test Equipment

Introduction The test method of Cavitation Corrosion and Erosion-Corrosion Characteristics Test Equipment is: pump the sample with a standard aluminum automobile water pump, run it for 100h under the conditions of 113 ºC, 103kpa and pump speed of 4600r / min, and then check the water pump to determine the degree of cavitation corrosion, and grade it according to the grading system table. Characteristic 1. The Cavitation Corrosion and Erosion-Corrosion Characteristics Test

Lubricating Grease Dropping Point Tester Introduction The Dropping Point Tester is designed and made as per the national standard of People’s Republic of China GB/T 4929 Lubricating grease- Determination of Dropping Point and ASTM D566 Standard Test Method for Dropping Point of Lubricating Grease. I. Main technical features 1. The oil bath is composed of heat resistant beaker, heater and electric motor. The heating power can be adjusted continuously. The temperature in oil

Summary This aniline point test equipment is designed and made as per test method one in national standard of People’s Republic of China GB/T262 Petroleum Products and Hydrocarbon Solvents-Determination of Aniline Point and Mixed Aniline Point. The standard GB/T262 is refer to standard ISO2977. It is also suitable for test method An in ASTM D611 Standard Test Methods for Aniline Point and Mixed Aniline Point of Petroleum Products and Hydrocarbon Solvents. I. Main technical

Petroleum Oils Multifunctional Pour Point Tester This pour point apparatus is refrigerated by imported compressor made by Danfoss Denmark.Adopting most advanced refrigeration technology,both troughs can reach to low temperature -70℃.Compared to other machines,our refrigeration performance is stable and, the compressor is durable. I.Main features 1.This pour point tester adopts double compressor cascade refrigeration,environment-friendly refrigerant,speedy cooling. 2.Imported

Herschel Emulsifier Water Separability Test Apparatus AIC-1401 water separability tester.pdf Introduction The water separability apparatus is suitable to measure the water separability of Petroleum Oils and Synthetic Fluids.Fill certain amount of sample and distilled water,stir 5 minutes under certain temperature,record needed time for separation of emulsified liquid.After half hour or one hour,if the emulsified liquid doesn’t separate completely,or the emulsified layers

Lubricating Grease Air Release Properties Value Test Apparatus Introduction The apparatus is suitable to test ability of oils to separate entrained air,such as turbine oil, hydraulic oil etc. Heat the oil sample to temperature 25,50 or 75℃,blow compressed air through the test oil,make make it stirred strongly.Air becomes small bubbles in the air,that is entrained air.After the air is stopped,the time required for the air entrained in the oil to reduce in volume to 0.2% is

Engine Oils HTHS High-Temperature and High-Shear Viscometer HTHS Introduction: The High-Temperature and High-Shear Viscometer is mainly used to determine the apparent viscosity of lubricating oil at high temperature and high shear rate. The test principle is to make the sample flow out from the capillary viscometer under the pressure of nitrogen (carbon dioxide) under the test condition of 150°C. By the outflow time and pressure of the sample, the apparent shear rate of

ASTM D445 Manual and Cheap Kinematic Viscosity Tester Summary This tester is suitable to determine kinematic viscosity of petroleum products. Principle:Under certain constant temperature,measure flow time of liquid with specified volume through one calibrated glass capillary(reverse flow type),multiplication of capillary constant and flow time is the kinematic viscosity of this liquid under that temperature. I. Main technical features 1.The heating bath is made of glass,which

Fully Automatic Cleveland Open Cup Flash Point Analyzer Introduction According to test method of GB/T3536,this open cup flash point analyzer adopts advanced Microprocessor and PID temperature controlling technology, the temperature rising speed is fast, temperature controlling is more precise, and test result is more accurate. LCD big screen replaces old design of RS323 port, the operation is easier. This machine is highly automatic, which can automatically calibrate

Apparent Viscosity Test at High Temperature and High Shear Rate Introduction: This HTHS is mainly used to measure apparent viscosity at high temperature and high shear rate(HTHS),the principle of which is under certain test condition at 150C,with pressure of N2(CO2),the sample flows out from capilliary viscometer,according to flowing time and pressure,we can calculate the apparent viscosity reached by apparent sheat rate of capillary viscometer. Features: 1.This apparatus is

Foaming Tendency Apparatus Bath with Cooler Introduction The tendency of oils to foam can be a serious problem in systems such as high-speed gearing, high-volume pumping, and splash lubrication. Inadequate lubrication, cavitation, and overflow loss of lubricant can lead to mechanical failure. This instrument is used in the evaluation of oils for such operating conditions. I.Main features 1.This Foaming Tendency Bath is separated,including heating bath and precise flowmeter 2

Extreme-Pressure Properties Tester for Lubricating Fluids (4 Ball Method) Introduction This Extreme Pressure Properties Test Machine uses four Ф12.7mm standard steel balls evaluate the load-bearing capacity and anti-wear performanceof lubricants (including oil film strength PB, sintering load PD, comprehensive wear value ZMZ, Long-term wear D and other indexes). The influence of temperature on the lubricating performance of lubricants can also be measured. Main Features: 1

Water Washout Tester for Lubricating Grease Introduction: This test method covers the evaluation of the resistance of a lubricating grease to washout by water from a bearing, when tested at 38 °C and 79 °C (100 °F and 175 °F) under the prescribed laboratory conditions. It is not to be considered the equivalent of service evaluation tests. Precision and bias was determined using grease ranging from NLGI 3 to 0 grades in the research report. Features: 1.The case of water

Petroleum Oils Solidifying Point&Cold Filter Plugging Point Testing Equipment Summary This instrument is newly designed and made as per national standard of People's Republic of China GB/T510 Standard Test Method for Solidifying Point of Petroleum Oils.It is suitable to determine solidifying point of petroleum products. It is widely used in oil exploitation companies, petroleum manufacturers, petroleum users, colleges and scientific research institutes. I. Main technical

Existent Gum Tester for Aviation Fuel Testing Summary This existent gum tester is designed and made as per standards GB/T 8019-2008 Standard test method for gum content in fuels by jet evaporation and ASTM D381. It can be used to determine the existent gum content of aviation fuels by steam vaporizing medium. Equipping with an air compressor, this instrument can also be used to determine the existent gum content of aviation gasolines and motor gasolines by air vaporizing

Density Tester for LPG and Light Hydrocarbons by Pressure Hydrometer Introduction: This instrument is suitable to determine the density of LPG and light hydrocarbons. ● Applicable standards:SH/T0221 ASTM D1657 ●Temperature controlling method:imported digital PID controller ● Temperature range:ambient~25℃ ● Refrigeration method:air compress ● Stirring method:magnetic stirring ● Power supply:AC220V±10%/50HZ Features: 1. Big power magnetic circulation system can guarantee the

High Temperature Lubricating Oils Foaming Characteristics Tester High Temperature Foaming Characteristics of Lubricating Oils: This Lubricating Oils Foaming Characteristics Tester is suitable for testing the foam properties of lubricating oils at 150ºC. The sample was heated to 49ºC, kept at a constant temperature for 30 min, and then cooled to room temperature. Then the sample was transferred to a specified cylinder and heated to 150ºC. The air was passed through the metal

Introduction This filter blocking tendency test instrument has built-in NB/SH/T 0895-2015 test requirements. The microcomputer processing controller, color touch screen, and USB data interface are equipped. The interface operation is simple. The built-in refrigeration module, weighing module, and high-precision pressure sensor ensure the test. The process of determining the filterability of distillate fuel oil with viscosity ranging from 1.70 to 6.20mm2/s (cSt) at 40ºC.

ASTM D92 Cleveland Open Cup Flash Point Apparatus Introduction This cleveland flash point Apparatus is suitable to determine flash point and fire point of petroleum products. Principle:fill the sample into sample cup with mark line.Firstly raise sample temperature quickly,then gradually.When near to flash point,constantly raise temperature.According to specified temperature interval,using small fire cross the sample cup,take the minimum temperature of steam flash on surface

H2S Hydrogen Sulfide Content Analyzer Introduction This H2S analyzer is fully designed according to requirements of ASTM and IP standards.Dilute few sample with dilution,heat the sample to 60℃ with metal bath being controlled under precise temperature,and release H2S in sample.Using clean air as carrier gas,carry H2S into measuring cell of electro-chemical sensor,and get the instant concentration of H2S.Air flow is measured and controlled by digital mass flow meter,and when