Oil Test Equipment

Introduction The sample circulates for 1064h at 88 ºC and a certain flow rate in a closed system composed of a reservoir, a water pump, a radiator and rubber pipes. Its corrosion resistance is determined by the weight loss of typical metal test pieces used in the engine cooling system installed in the reservoir and the state surface of the internal surface of each component visually. The performance change of the sample is determined by analyzing the samples taken from the

The TFOUT Tester adopts a full-automatic control system. The operator can automatically test and print the results as long as the sample is put into the instrument. The whole process does not require manual conduct. The principle is to put the sample, distilled water and copper catalyst coil into the glass tube together, and then put it into the oxygen bomb. The oxygen bomb is filled with oxygen at room temperature and put into the oil bath at the specified temperature. The

SummaryThis Automated Houillon Viscometer is manufactured according to Nb/SH/T 0956-2017 folding tube type automatic viscometer method for measuring the kinematic viscosity of transparent and opaque liquids.This Automated Houillon Viscometer automatically cleans, dries and calculates the results. It can also calculate the viscosity index.Combined with micro detection, this Automated Houillon Viscometer has advantanges of labor and consumables are saved, and the detection

Detailed Photos Product Description Introduction This H2S Hydrogen Sulfide Content Tester is fully designed according to requirements of ASTM and IP standards. Dilute few sample with dilution,heat the sample to 60ºC with metal bath being controlled under precise temperature,and release H2S in sample.Using clean air as carrier gas,carry H2S into measuring cell of electro-chemical sensor,and get the instant concentration of H2S.Air flow is measured and controlled by digital

Summary The Scanning Brookfield measures the low-temperature pumpability and gelation index of new oil, smoky and highly oxidized engine Oils by continuously recording viscosity values in a wide temperature range. This Low Temperature Viscosity/Gelation Index Test Apparatus is compilied with ASTM D5133, ASTM D7110, SH/T0732, GB/T 11121 and other standard test methods, and it is specified instrument for ASTM D5133. Working principle: measure the low temperature pumpability and

Summary This FTIR testing equipment is designed and manufactured in accordance with the requirements of the People's Republic of China Standard GB/T 23801 "Determination of fatty acid methyl ester content in middle distillate oil by infrared spectroscopy" and the industry standard NB/SH/T 0916 "Determination of biodiesel (fatty acid methyl ester) content in diesel fuel by infrared spectroscopy". This FTIR testing equipment adopts Fourier transform infrared spectroscopy, which

Introduction: This Rusting Prevention Testeris mainly used to test the rust preventing characteristics of mineral oil with inhibitor, especially the gas turbine oil when mixed with water. The Rusting Prevention Tester is also suitable for detecting other oil products, such as hydraulic oil, circulating oil and liquid with specific gravity of water. The operating principle is: mix a certain amount of sample with distilled water or synthetic seawater, immerse all cylindrical

Summary This Multifunctional Viscosity Index ,Kinematic Viscosity,Density Analyzer is designed and made as per national standard of People's Republic of China GB/T 1884, GB/T 265 and GB/T 1995. It can determine the density(liquid petroleum products) as per GB/T 1884, the kinematic viscosity(Newtonian liquids) as per GB/T 265 and viscosity index(Lubricating oils) as per GB/T 1995. I.Main features 1. The Multifunctional Viscosity Index ,Kinematic Viscosity,Density Analyzer can

Introduction This wax melting point apparatus is suitable for detecting the melting point of paraffin, unsuitable for microcrystalline wax and petroleum grease. Main Festures: 1. Two hole operation is convenient for parallel sampling; 2. Adopt semiconductor refrigeration; 3. Metal thermostatic bath, no need to add heat conduction medium; 4. Separate temperature control system; 5. Integrated structure, small and beautiful appearance; 6. Imported PID temperature controller,

.Introduction This 4 ball test machine uses four Ф12.7mm standard steel balls evaluate the load-bearing capacity and anti-wear performanceof lubricants (including oil film strength PB, sintering load PD, comprehensive wear value ZMZ, Long-term wear D and other indexes). The influence of temperature on the lubricating performance of lubricants can also be measured. Main Features: 1.Adopting double floating bearing technology, no-clearance guiding technology and buffer cross

Detailed Photos Product Description Summary The lubricating oil aging characteristic tester is applicable to measuring the aging characteristics of petroleum based lubricating oil,which have an evaporation loss of less than 15 % mass fraction, and the petroleum based lubricating oil with or without additives. It is also suitable for lubricating oils with antioxidant additives and ash cleaning dispersants. I. Main technical features 1.The aging characteristic tester is a bench

Summary This Flow Ability Test Instrument is applicable to determine ability to flow of lubricating oil. The operating principle is to measure the rising speed of lubricating oil in the U-shaped pipe under constant pressure and specified low temperature conditions, which is expressed by the temperature when the rising speed under such conditions is 10mm/min. I. Main technical features 1. The Flow Ability Test Instrument adopts Double compressor cascade refrigeration ensures

Summary The test principle of the Floc Point Test Instrument is as follows: mix a certain amount of sample and refrigerant in the test tube, put them into the cold bath of the floc point tester after mutual dissolution, gradually cool them down at a certain speed, observe under the light, and record the temperature at this time when the milky or flocculation phenomenon begins to appear. The Floc Point Test Instrument is applicable to mineral oil refrigerator oil and synthetic

Summary This Seal Compatibility Index Test Apparatus is suitable for the determination of various petroleum products, but it is not suitable for the determination of water containing petroleum products. Measure the inner diameter of the rubber ring with a conical gauge, then soak the rubber ring in the sample at a certain temperature for 24 hours, take it out for cooling, and measure the change of the rubber inner diameter with a conical gauge. I. Main technical features 1

Summary This Carbonizable Substances Test Instrument is suitable for detecting the easily carbonizable substances in white oil. The principle is that the white oil is treated with concentrated sulfuric acid, and the reflected acid layer color is compared with the standard colorimetric solution, so as to determine the test results. I. Main technical features 1. Standard colorimetric tube, conforming to ASTM requirements; 2. The Carbonizable Substances Test Instrument has a set

Summary This Lubricating Oils Filterability Test Equipment is produced according to SH/T 0805 standard and is used to determine the filterability of lubricating oil based on mineral oil, especially hydraulic oil in hydraulic system. It is not applicable to liquids based on other materials (such as flame retardant liquid, which may be compatible with the filter membrane used in this method). This Lubricating Oils Filterability Test Equipment is also not applicable to some

Introduction: This Oxidation Characteristics Analysis Equipment is manufactured according to SH/T 0123-93 standard and is applicable to the determination of extreme pressure lubricating oil (such as gear oil). The use method is: the sample is injected with constant pressure dry air at a certain temperature, and the test lasts for 312 hours. The oxidation stability of the oil is indicated by measuring the increase value and precipitation value of the kinematic viscosity of the

Summary The Aging Characteristics Test Instrument is applicable to measuring the aging characteristics of petroleum based lubricating oil,which have an evaporation loss of less than 15 % mass fraction, and the petroleum based lubricating oil with or without additives. It is also suitable for lubricating oils with antioxidant additives and ash cleaning dispersants. I. Main technical features 1.The Aging Characteristics Test Instrument is a bench type, including a stainless

Summary KRL Tapered Roller Bearing method determines viscosity and shear stability of Transmission Lubricants, This KRL Taper Roller Bearing Rig adopts LCD touch screen: through the screen, the oil sample temperature control, rotating shaft speed, test load, test time, shear revolution and other functions can be controlled. All key parameters and control points can be displayed at a glance, realizing a highly integrated and automated operation interface, which greatly reduces