Oil Test Equipment

Product Description The Automatic FAME Rancimat Oxidation Stability Test Equipment is manufactured in accordance with NB/SH/T 0873-2013 "Determination of Oxidation Stability of Biodiesel and Its Harmonic Fuels. Other applicable standards are as follows: NB/SH/T 0825, EN14112, EN15751, EN16568, ISO6886, GB/T 21121. The measurement principle of the Automatic FAME Rancimat Oxidation Stability Test Equipment is that the sample is placed in a constant temperature aluminum heating

Product Description ASTM D2619 Hydrolytic Stability Tester for Hydraulic Fluids (Beverage Bottle Method) This Hydrolytic Stability Tester is suitable for testing hydrolytic stability of mineral oil and synthetic hydraulic fluid, as well as evaluating water-based or water emulsified hydraulic fluid. During the test, the sample, water and copper strip instrument shall be sealed in the pressure resistant glass, and then placed in the oil hydrolytic stability test box at a

Introduction This smoke point tester is made according to GB/T382-83 and ASTM D1322. It is used to test smoke point of kerosene and jet fuel in a standard lamps and lanterns, to measure the maximum height of smokeless flame in burning conditions. Main Features 1. Sample combustion in the standard lamp, flame height changes reflected on the mm scale background 2. The structure of the instrument is compact and integrity 3. No circuit element 4. Repeatability of determination

Introduction This Asphaltenes Testing Equipment is suitable for petroleum products and samples whose temperature is lower than 80ºC and can flow. It is also suitable for the measurement of petroleum asphalt and residual oil. A membrane filter of known weight is filtered, then dried, and then the weight of the insoluble matter filtered by the membrane filter is weighed. The principle of measuring asphalt is to use n-heptane to precipitate asphaltenes from the sample. After

Introduction Coat the sample on a new bearing and run it for 60 seconds under a light thrust load to distribute the grease as it is used. The bearing is stored for 48 hours at 52 degrees and 100% relative humidity, and then clean and inspect for signs of corrosion on the outer ring raceway of the bearing. Main feature ◆ The Corrosion Preventive Properties Analyzer is equipped with a set of mechanical greasers and a set of thrust loader; ◆ Automatically control the running

I.Introduction ASTM D1742 Oil Separation Test Equipment covers the determination of the tendency of a lubricating grease to separate oil during storage in both normally filled and partially filled containers. This Oil Separation Test Equipment is not suitable for greases softer than NLGI No. 1 grade. II.Main Features: 1.This Lubricating Grease Oil Separation Test Equipment adopts digital gauge shows pressure, the result is clear at a glance. 2.High precision needle valve

Significance and Use This Fafnir Friction Oxidation Tester is used to evaluate the property of lubricating greases to protect oscillating bearings from fretting wear. This method, used for specification purposes, differentiates among greases allowing low, medium, and high amounts of fretting wear under the prescribed test conditions. The test has been used to predict the fretting performance of greases in wheel bearings of passenger cars shipped long distances.5 Test results

Introduction This auto kinematic viscometer can test viscosity of liquid with high degree of equipment automation.Measurement, cleaning, drying, result calculation, and printing are all automatically completed. Characteristic 1.This auto kinematic viscometer adopts microcontroller control and color touch screen display, stable and reliable; 2.Wide measurement range, different viscosities only require replacing the glass viscometer; 3.Good human-machine interface for easy

I.General Introduction This petroleum wax penetrometer is suitable for detecting the penetration of solid and semi solid asphalt materials with a penetration of less than 350, and is also suitable for asphalt materials with a penetration of 350-500. II. Technical Specification 1 Applicable standard: GB/T4985,ASTM D1321 2. Time: ≤ 60s. 3. Needle mass: 2.5 g ± 0.05g. 4. Plunger mass: 47.5 ± 0.05g. 5. Measurement value: < 620. 6. Working power supply: AC220V ± 10%/50HZ. III

Introduction This Corrosive Sulfur Analyzer is used to determine corrosive sulfur compounds (both inorganic and organic) in electrical insulating liquids. New and in-service insulating liquids may contain elemental sulfur or sulfur compounds, or both, that cause corrosion under certain conditions of use. This Corrosive Sulfur Analyzer is designed to detect the presence of, or the propensity to form, free (elemental) sulfur and corrosive sulfur compounds by subjecting copper

Introduction This instrument is a fully Automatic Pour Point and Solidification Point Analyzer controlled by a computer. User only need to install a glass test tube with a sample into a cold bath, and the instrument will automatically test according to standard requirements. Main Features 1. The Automatic Pour Point and Solidification Point Analyzer mainly consists of refrigeration system, control system, measurement system, etc. 2. The refrigeration system consists of a two

Introduction The sample circulates for 1064h at 88 ºC and a certain flow rate in a closed system composed of a reservoir, a water pump, a radiator and rubber pipes. Its corrosion resistance is determined by the weight loss of typical metal test pieces used in the engine cooling system installed in the reservoir and the state surface of the internal surface of each component visually. The performance change of the sample is determined by analyzing the samples taken from the

The TFOUT Tester adopts a full-automatic control system. The operator can automatically test and print the results as long as the sample is put into the instrument. The whole process does not require manual conduct. The principle is to put the sample, distilled water and copper catalyst coil into the glass tube together, and then put it into the oxygen bomb. The oxygen bomb is filled with oxygen at room temperature and put into the oil bath at the specified temperature. The

SummaryThis Automated Houillon Viscometer is manufactured according to Nb/SH/T 0956-2017 folding tube type automatic viscometer method for measuring the kinematic viscosity of transparent and opaque liquids.This Automated Houillon Viscometer automatically cleans, dries and calculates the results. It can also calculate the viscosity index.Combined with micro detection, this Automated Houillon Viscometer has advantanges of labor and consumables are saved, and the detection

Detailed Photos Product Description Introduction This H2S Hydrogen Sulfide Content Tester is fully designed according to requirements of ASTM and IP standards. Dilute few sample with dilution,heat the sample to 60ºC with metal bath being controlled under precise temperature,and release H2S in sample.Using clean air as carrier gas,carry H2S into measuring cell of electro-chemical sensor,and get the instant concentration of H2S.Air flow is measured and controlled by digital

Summary The Scanning Brookfield measures the low-temperature pumpability and gelation index of new oil, smoky and highly oxidized engine Oils by continuously recording viscosity values in a wide temperature range. This Low Temperature Viscosity/Gelation Index Test Apparatus is compilied with ASTM D5133, ASTM D7110, SH/T0732, GB/T 11121 and other standard test methods, and it is specified instrument for ASTM D5133. Working principle: measure the low temperature pumpability and

Summary This FTIR testing equipment is designed and manufactured in accordance with the requirements of the People's Republic of China Standard GB/T 23801 "Determination of fatty acid methyl ester content in middle distillate oil by infrared spectroscopy" and the industry standard NB/SH/T 0916 "Determination of biodiesel (fatty acid methyl ester) content in diesel fuel by infrared spectroscopy". This FTIR testing equipment adopts Fourier transform infrared spectroscopy, which

Introduction: This Rusting Prevention Testeris mainly used to test the rust preventing characteristics of mineral oil with inhibitor, especially the gas turbine oil when mixed with water. The Rusting Prevention Tester is also suitable for detecting other oil products, such as hydraulic oil, circulating oil and liquid with specific gravity of water. The operating principle is: mix a certain amount of sample with distilled water or synthetic seawater, immerse all cylindrical

Summary This Multifunctional Viscosity Index ,Kinematic Viscosity,Density Analyzer is designed and made as per national standard of People's Republic of China GB/T 1884, GB/T 265 and GB/T 1995. It can determine the density(liquid petroleum products) as per GB/T 1884, the kinematic viscosity(Newtonian liquids) as per GB/T 265 and viscosity index(Lubricating oils) as per GB/T 1995. I.Main features 1. The Multifunctional Viscosity Index ,Kinematic Viscosity,Density Analyzer can

Introduction This wax melting point apparatus is suitable for detecting the melting point of paraffin, unsuitable for microcrystalline wax and petroleum grease. Main Festures: 1. Two hole operation is convenient for parallel sampling; 2. Adopt semiconductor refrigeration; 3. Metal thermostatic bath, no need to add heat conduction medium; 4. Separate temperature control system; 5. Integrated structure, small and beautiful appearance; 6. Imported PID temperature controller,