HDPE Pipe Fittings

HDPE Pipe Fittings HDPE reducer Description HDPE reducer has its own unique advantages, and is widely used in building water supply, building drainage, buried drainage pipe, building heating, gas transmission pipe, electrical and telecommunication protection sleeve, industrial pipe, agricultural pipe, etc. It is mainly used in urban water supply, urban gas supply and farmland irrigation. HDPE reducer has good sanitation, self-cleaning, anti-bacterial, long-term use does not

Description PE butt saddle type pipe fittings lead out new branch pipe in the original pipeline, generally only the side port belongs to the rest of the pipeline and plays a fixed role.PE butt saddle pipe is a straight, three-way and four-way pipe with HDPE as raw material.It can replace flange tee, cross grafting branch pipe, with the advantages of simple installation, fast, accurate location and so on. Generally, only the side port of butt saddle type pipe fittings belongs

Description HDPE socket saddle type pipe fitting is one of PE pipe fittings, and its connection principle and process are basically the same as PE socket pipe fittings.For different PE saddle type pipe fittings, the following methods shall be used for fastening: If the PE socket saddle type pipe fittings have semi-circular groove shaped lower fastener, the section with reinforcement edge shall be fastened with wooden or rubber hammer.Slide it along the pipe from one end of

Description HDPE hot-melt injection butt joint tee with the same diameter is a pipe fitting and pipe connector, which is used at the branch pipe of the main pipe.Equal tee is a kind of tee. There are general equal tee and reducing tee. It is named because the three ends can be connected with the pipe. HDPE hot-melt butt joint tee is a molded tee. Its connection form is to directly butt joint the tee with the plastic pipe.The main manufacturing standard of HDPE butt tee is

HDPE product HDPE butt tee Description of HDPE butt tee HDPE butt tee is a new product made of high-quality polyethylene resin as the main material, adding necessary antioxidants, ultraviolet absorbents and other additives through extrusion processing. It is widely used in municipal water supply, drainage, petrochemical, mining, farmland irrigation, sewage, mortar transportation, waste landfill and other pipeline projects. HDPE butt tee is produced with high-quality raw

HDPE specification HDPE butt elbow Description of HDPE butt elbow HDPE butt elbow is made of polyethylene plastic, PE is a basic plastic material, plastic bags, plastic film are PE products. HDPE is a high crystallinity, non-polar thermoplastic resin. The appearance of the original HDPE is milky white and translucent to a certain extent in the thin section. HDPE has excellent resistance to most domestic and industrial chemicals. Technical data sheet of HDPE butt elbow HDPE

HDPE Pipe Fittings HDPE cross Description HDPE cross is a high crystallinity, non-polar thermoplastic resin material made of pipe fittings. The appearance of the original HDPE is milky white and translucent to a certain extent in the thin section. HDPE has excellent resistance to most domestic and industrial chemicals. HDPE cross. Its elongation at break is not less than 350%, which can reach more than 500%. It has strong adaptability to uneven settlement of pipe foundation

HDPE Pipe Fittings HDPE elbow Description HDPE elbow silent building drainage pipe fittings contain anti oxidant and anti ultraviolet (UV) additives, which are extruded by extruder. The product has the advantages of anti-oxidation, high strength, good wear resistance, excellent corrosion resistance, impact resistance, low temperature resistance, self-lubricating and low flow resistance. The pipe fittings are filled with grooves, and the pipe joints are scraped by a special

Description Reducer, also known as reducer, is one of the chemical pipe fittings, which is used for the connection of two different pipe diameters.According to different types, it can be divided into concentric reducer and eccentric reducer.When the flow rate of the fluid in the pipeline changes, such as increasing or decreasing, and the flow rate requirement changes little, reducer shall be used. At the inlet of the pump, in order to prevent cavitation, a reducer is needed

Description The pipe cap, also known as the head, is a pipe fitting welded on the pipe end or installed on the external thread of the pipe end to cap the pipe.The cap is used to close the pipeline, and has the same function as the pipe plug.HDPE electrofusion pipe cap is a kind of plastic pipe fittings which can be connected by melting through the temperature generated by current. In the process of installation, there should be no organic matters or pollutants in the inner

Description Preparation before welding: the same as ordinary welding.Mark out the welding area on the pipe.Clean the welding surface, scrape the welding surface within the scribed area about 0.2mm to remove the oxide layer, and the scraped area shall be larger than the oxide layer. For the installation of pipe fittings, the method provided by the manufacturer shall be used to ensure that there is no gap between the welding surface of PE electric melting saddle pipe fittings

Hydraulic pipe fitting HDPE butt elbow Description of HDPE butt elbow HDPE butt elbow has complete size, complete accessories, small expansion rate, impact resistance, Gao pressure resistance, Fu wear resistance. Generally, it is connected by hot-melt butt welding, which saves space and materials, is simple and fast, safe and leak proof. In addition, it is connected by electric welding pipe hoop, with insurance indication, which can control the welding time, and is suitable

Plastic pipe fitting HDPE butt tee Description of HDPE butt tee HDPE butt tee is made of opaque white waxy material, with a specific gravity of 0.941 ~ 0.960, which is lighter than water. It is soft and tough, but slightly harder than LDPE, slightly elongated, non-toxic and tasteless. The tee made of this material is flammable and can continue to burn after leaving the fire. The upper end of the flame is yellow and the lower end is blue. It will melt when burning, with liquid

HDPE Pipe Fittings HDPE tee Description HDPE tee is made by polymerization of monomer ethylene. Due to different pressure, temperature and other polymerization conditions, HDPE can be extracted from resin with different density, so it is different from HDPE, MDPE and LDPE. Technical data sheet HDPE Pipe Fittings HDPE tee technical data sheet as below: Specification and dimension of electric-melt 45° elbow Product specification D/mm D/mm L/mm A/mm 45°L 50 50 160 60 45°L 63 63

HDPE Pipe Fittings HDPE elbow Description HDPE elbow is made of pure polyethylene, which has excellent low temperature resistance, good flexibility, impact resistance, wear resistance, smooth inner wall, and improved medium mass flow rate. According to the national standard design, production, high interface strength. With the same type of pipe hot-melt connection, easy to install. The connection is firm without water leakage. In the production process, strict selection of

HDPE Pipe Fittings HDPE tee Description HDPE tee uses high density polyethylene as the main material, which has the characteristics of sound insulation, heat resistance and high strength of cast iron pipe, as well as the characteristics of plastic pipe toughness, smoothness, easy installation, energy conservation and environmental protection. At the same time, it also overcomes the disadvantages of heavy quality of cast iron pipe, high engineering comprehensive cost, low

HDPE Pipe Fittings HDPE elbow Description HDPE elbow has good impact resistance at low temperature and extremely low brittleness temperature. It can be used safely in the temperature range of - 60-60 ℃. In winter construction, due to the good impact resistance of materials, the elbow will not be brittle. At the same time, it has good stress cracking resistance, low notch sensitivity, high shear strength and excellent scratch resistance, and environmental stress cracking

Description It is applicable to the connection of all specification pipes of the same material and SDR system.It is applicable to the connection of pipes with different grades of the same grade of materials.Reliable connection performance, high interface strength, good air tightness and stable fusion performance. It can effectively resist oxidation and corrosion, and ensure the stability of welding performance.It is not easy to be affected by environmental temperature change

Description It is applicable to the connection of all specification pipes of the same material and SDR system.It is applicable to the connection of pipes with different grades of the same grade of materials.Reliable connection performance, high interface strength, good air tightness and stable fusion performance. It can effectively resist oxidation and corrosion, and ensure the stability of welding performance.It is not easy to be affected by environmental temperature change

Description It is applicable to the connection of all specification pipes of the same material and SDR system.It is applicable to the connection of pipes with different grades of the same grade of materials.Reliable connection performance, high interface strength, good air tightness and stable fusion performance. It can effectively resist oxidation and corrosion, and ensure the stability of welding performance.It is not easy to be affected by environmental temperature change