Energy Saving Hollow Cup 24V Brushless Motor High Speed Low Noise
High Quality 24V High Speed Low Noise Hollow Cup Brushless Motor
Advantages of hollow cup brushless motor:
1. Energy saving characteristics: the energy conversion efficiency is very high, the maximum efficiency is generally more than 70%, and some products can reach more than 90% (iron core motor is generally 20-50%).
2. Control characteristics: rapid start and braking, extremely fast response, mechanical time constant less than 28 milliseconds, and some products can reach less than 1 milliseconds (iron core motors are generally more than 100 milliseconds); In the high-speed operation state in the recommended operation area, the speed can be adjusted sensitively and conveniently
3. The driving characteristics and operation stability are very reliable, and the speed fluctuation is very small. As a micro motor, its speed fluctuation can be easily controlled within 2%.
In addition, the energy density of hollow cup motor is greatly improved, and its weight and volume are reduced by 1 / 3-1 / 2 compared with iron core motor with the same power.
Standard Type
| Motor Paremeters(25℃) |
Part No. |
With Hall Sensors | LEC-4P2266 -001 | LEC-4P2266 -002 | LEC-2266-0 03 | |||||||||||
| 1 | Nominal Power | P | W | 90W | 90W | 90W | ||||||||||
| 2 | Rated Voltage | U | V | 24 | 48 | 24 | ||||||||||
| 3 | No load speed ± 10% | N0 | rpm | 16500 | 16900 | 15000 | ||||||||||
| 4 | No load current ±50% | I0 | m A | 233 | 112 | 230 | ||||||||||
| 5 | Nominal speed | nN | rpm | 15000 | 15800 | 13200 | ||||||||||
| 6 | Nominal torque | MN | mNm | 54.5 | 54.5 | 35 | ||||||||||
| 7 | Nominal current | IN | A | 4.5 | 2.1 | 2.37 | ||||||||||
| 8 | Stall torque | MH | mNm | 950 | 1020 | 335.9 | ||||||||||
| 9 | Stall current | IH | A | 70.8 | 37.7 | 22. 1 | ||||||||||
| 10 | Speed constant | Kn | rpm/V | 704 | 352 | 625 | ||||||||||
| 11 | Torque constant | KM | mNm/A | 13.52 | 27. 1 | 15.24 | ||||||||||
| 12 | Terminal resistance ± 10% | R | Ω | 0.34 | 1.27 | 1.0 | ||||||||||
| 13 | Terminal inductance | L | mH | 0.21 | 0. 123 | 0.21 | ||||||||||
| 14 | Rotor inertia | J | g ·cm2 | 6.8 | 8.91 | 7.8 | ||||||||||
| 15 | Mechanical time constant | τm | ms | 1.5 | 1.54 | 1.8 | ||||||||||
| Characteristic parameters | Range of operation | Definition of wiring | ||||||||||||||
| 16 | Weight | 125g | Winding of motor | |||||||||||||
| 17 | length of shaft (Acceptance of customization) | U | V | W | ||||||||||||
| 18 | Ambient temperature -40℃ ~ +100℃ | Red | Black | White | ||||||||||||
| 19 | Max. winding temperature 130℃ | Hall line | ||||||||||||||
| 20 | Number of phases 3 | H+5V | HGND | HU | HV | HW | ||||||||||
| 21 | Number of pole pairs 2 | Red | Black | Yellow | Brown | Gray | ||||||||||
| 22 | Length of cable(Length of standard 300mm±10mm),acceptance of customization | Electric motor cable: Hall sensor: | ||||||||||||||
Motor assembly configuration
| Gearbox | Feedback device | ||||||||||||
| Planetary | Encoder | ||||||||||||
| Standard: | GPA22 | Match: MENC20- 1024 (Magnetic encoder) | |||||||||||
| Reduction ratio X :1 | Level 1 | Level 2 | Level 3 | Level 4 | Level 5 | Optional:ENC20- 1000/ 1024/2000/2048 (Grating encoder) | |||||||
| 3.5 | 4.6 | 12.76 | 16.00 | 45.55 | 51.02 | 162. 19 | 182.22 | 581.05 | 650.77 | Resolver | |||
| 4.0 | 14.29 | 18.40 | 64.00 | 73.60 | 204.08 | 228.57 | 748.39 | 838. 19 | If you need other encoders, please consult the manufacturer. | ||||
| 21. 16 | 116.38 | 139. 15 | 256.00 | 302.29 | 938.78 | 1079.59 | Optional brake | ||||||
| 389.34 | 1241.53 | 1557.3 | 24 VDC brake | ||||||||||
| 1790.98 | 1177.60 | Drive | |||||||||||
| Length(mm) | 1354.24 | 2059.63 | Drive ( three rings) | Drive ( three rings) | Imported drive | ||||||||
| 21.4 | 27 | 30.8 | 34.6 | 38.4 |
LDP-4805 LDP-4810 LDP-4815 LDP-4815R |
LDV-4805 (LDV domestic device 92%) LDM-4820 ( LDM domestic device 100%) |
Elmo Copley |
||||||
| The above is the partial speed ratio of GPA22 , all levels of speed ratio can be selected; Reducer temperature: -40℃ ~ +100℃, if you need to match other reducer, please consult the manufacturer. | |||||||||||||
| Harmonic gearhead Worm gear Low backlash | |||||||||||||
Warehouse and production line:
FAQ:
Q: How to order?
A: send us inquiry → receive our quotation → negotiate details → confirm the sample → sign contract/deposit → mass production →cargo ready → balance/delivery → further cooperation
Q: What’s the payment term ?
A: Payment by T/T or L/C. Sample order should be 100% prepaid. For bulk order, 50% deposit, the balance paid before shipping.
Q: Which shipping way is available ?
A: Sample or small order by DHL,UPS,FedEx. Bulk order by Air or by Sea.
Q: How long is the delivery time ?
A: Sample order takes 7-15 workdays. Bulk order takes 25-30 workdays.
Q: My package has missing products. What can I do?
A: Please contact our support team and we will confirm your order with the package contents. We apologize for any inconveniences.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.